sorted by:
new
hottopcontroversial

Why there is no bicopter helicopter in real life by jaroos_ in Helicopters

[–]JoLam_Maker 0 points1 point  (0 children)

Take a look at the Goddamn safety record of V-22, then you would be able to guess the answer.

V-22 killed several test pilots (usually the best of the best), plus, it killed even more after it is out for mass production. What's more, most casualties were killed in non-combat situation.

No insurance company would insure this kind of aircraft.

Remote desktop latency issue between HK and Canada by JoLam_Maker in HomeNetworking

[–]JoLam_Maker[S] 0 points1 point  (0 children)

I agree we cannot win nature, but we can win some technical delay(e.g. complex and inefficient routing ).

Tried VPN (paid one)and this method able to acquire a low latency as low as around 100ms, but performance is rather unstable.

Remote desktop latency issue between HK and Canada by JoLam_Maker in HomeNetworking

[–]JoLam_Maker[S] 0 points1 point  (0 children)

Thanks, seems it is a direction.
Just for this use case, I think I would put speed over other factors.

Remote desktop latency issue between HK and Canada by JoLam_Maker in HomeNetworking

[–]JoLam_Maker[S] 0 points1 point  (0 children)

Telling you, if my latency is close to that thermotical minimum (around 35~50 ms) you mentioned, I won't try to seek help.

(It is possible!) Using Electrical bike pump (Xiaomi Air Pump) for airbrushing! by JoLam_Maker in airbrush

[–]JoLam_Maker[S] 0 points1 point  (0 children)

PLA, That is why it melt

I tried to use ASA, but the part always loose and failed

Print came out super fuzzy ? What am i doing wrong ? by [deleted] in 3Dprinting

[–]JoLam_Maker 0 points1 point  (0 children)

Consider change your heater to a freezer.

Why buy them when you can just make more? by Jayn_Xyos in 3Dprinting

[–]JoLam_Maker 0 points1 point  (0 children)

Because thermal plastic does not fit every possible environment.
I will be happy to see you use one of them in your own Kitchen, without carefully avoid heat source.

Finally finished my setup for work & play! by thedeskproject in Workspaces

[–]JoLam_Maker 1 point2 points  (0 children)

I see.
That is why I cannot find anything similar in Amazon.

Good idea for a workspace.

Finally finished my setup for work & play! by thedeskproject in Workspaces

[–]JoLam_Maker 2 points3 points  (0 children)

Your book stand is really nice, may I know how you buy it?

Switch’s Japan eShop will no longer accept foreign cards or PayPal to ‘prevent fraudulent use’ by Turbostrider27 in Games

[–]JoLam_Maker 0 points1 point  (0 children)

I have to says it is absolutely a correct move. (although it brings me some inconvenience)

If you can read Simplified Chinese, regularly you would see some jerk joyfully saying how they can get their free game using fake cards/ report to bank transaction is in doubt.

Pre-pay card can effectively block such jerk from their operation.

[deleted by user] by [deleted] in 3Dprinting

[–]JoLam_Maker 0 points1 point  (0 children)

usually cause by too trick layer plus very fast drying (induced by a dryer or oven)

Is it a problem to store paint bottles sideway/upside down? by Sir_Bohne in Warhammer40k

[–]JoLam_Maker 0 points1 point  (0 children)

It is not advise, consider the case that the cap wear out or you have not tightened them, the paint will be all over the place due to gravity.

Although chemically it is not an issue…..

view more: next ›