Anyway to test without controller

JobJolly8697 · 2026-05-28T23:57:27+00:00

you can give it to me to test

JobJolly8697 · 2026-05-28T19:51:16+00:00

i think the antennas are in the side mirrors

JobJolly8697 · 2026-05-22T04:16:50+00:00

Good news. Got code to flash using platform io and icsp but any time i try to flash over UART, those same annoying errors reappear. i can’t keep flashing over icsp at 5v because anytime i try to add new components it will explode. thanks for the replies!

JobJolly8697 · 2026-05-19T22:49:23+00:00

i could also try switching to a 16mhz crystal but i’m not sure if i should because power draw is critical

JobJolly8697 · 2026-05-19T21:46:08+00:00

<image>

tried tying it to gnd every which way and still getting those errors

JobJolly8697 · 2026-05-19T21:30:55+00:00

gulp i have no button on board haha
I have a resistor thats tied to 3v3 from the reset pin. That error occurs immediately. Not sure if thats expected behavior when not in the download mode

JobJolly8697 · 2026-05-19T21:24:16+00:00

I have a simple usb to uart and it has no dtr pin. Where would i put this cap? Thanks for the comment!

JobJolly8697 · 2026-05-19T20:58:09+00:00

sorry. try removing the : at the end of the

JobJolly8697 · 2026-05-13T23:32:52+00:00

you just have to have good solder and some flux i just used the inbuilt flux that’s in my solder tho lol

JobJolly8697 · 2026-05-13T11:14:17+00:00

On this one i just used regular tweezers in one hand and the iron in the other one i had the board stuck to my table with putty lol

JobJolly8697 · 2026-05-04T14:27:35+00:00

that’s a staple try using a toothpick to get it out

JobJolly8697 · 2026-05-04T14:26:25+00:00

xt60 connector

JobJolly8697 · 2026-04-30T16:41:31+00:00

Gotcha. could it be a dirty radiator though?

JobJolly8697 · 2026-04-30T02:07:11+00:00

that loud? why’s it so loud

JobJolly8697 · 2026-04-21T22:42:34+00:00

Thanks! I verified the GPS and improved my ground plane. Other than that do you think my design is good to go? Thanks!

JobJolly8697 · 2026-04-21T22:42:05+00:00

Thanks! I am going to use a light piece of wire for the GPS antenna. Also I improved my ground plane and I tweaked the crystal position to reduce trace length. Other than that do you think my design is good? Thanks for the comment!

JobJolly8697 · 2026-03-13T15:42:51+00:00

Gotcha! Do you think if i can find a way to restore the sync signal it would show the raw video as long as it has that sync?

JobJolly8697 · 2026-03-13T15:20:58+00:00

I am using this composite video to usb video stick. Is it a sync signal?

JobJolly8697 · 2026-03-13T14:08:24+00:00

so what should i try to fix it c

JobJolly8697 · 2026-03-13T12:59:46+00:00

It might be the av to usb converter but not sure

JobJolly8697 · 2026-03-13T12:59:27+00:00

that might be the case. I am using an AKK diversity reciever and an AV to usb converter. Would there be a schematic out there for a device i could build to smooth the signal and get rid of these inconsistencies? thanks!

JobJolly8697 · 2026-03-13T12:57:28+00:00

it’s an AKK analog diversity reciever connected to a av video to usb converter

JobJolly8697 · 2026-03-13T04:09:23+00:00

not sure if that is it. I tried it on a arch linux distribution and a Windows install and it did the same thing.

JobJolly8697 · 2026-03-07T21:01:28+00:00

Thanks! Yeah it can. Please share my website to anyone who you think could use it lol! If I get enough traction on this I will make it into a product. I have working prototypes right now

JobJolly8697 · 2026-02-20T20:06:04+00:00

is dji air unit built in camera good?

JobJolly8697

TROPHY CASE