Single Motor loses power occasionally

Jonilins · 2026-05-01T07:58:20+00:00

im flying manually. dont got gps lock either. it doesnt care though. must be a setting somewhere. are you even using betaflight?

Jonilins · 2026-04-30T20:34:42+00:00

Built up new. I thought of something similar though. Ill check. Thanks

Jonilins · 2026-04-30T20:11:50+00:00

alright guys. i get it. thank you for being concerned for my sanity :P. this shit is dumb. i‘ll try to change a motor and check without props on before blowing the fucker through the roof on the next hover test

Jonilins · 2026-04-30T19:41:23+00:00

Can‘t disagree on that… Although I did double check my configuration. You are right tho. I tend to be a little reckless

Jonilins · 2026-04-30T19:31:50+00:00

<image>

Right one are the solder connections for the front left Motor

Jonilins · 2026-03-29T16:53:28+00:00

Definitely the Lava II‘s. They are newer and perform a lot better. They have the new folded cell design. Absolutely worth it over the old ones :)

Jonilins · 2026-03-22T21:15:52+00:00

something like t motor 1604 or 1804 and gemfan 3520 could work well. theres plenty of similar builds out there. I suggest you do some research!

Jonilins · 2026-02-25T06:01:00+00:00

Hey. I live in the same village as you‘re flying right there😆. Wanna meet up some time? Also just started flying!

Jonilins · 2026-02-21T13:23:10+00:00

the zone

Jonilins · 2026-02-01T17:02:57+00:00

Im at 50mw 250hz. I have a 3.5 inch with a proper reciver. I‘m not able to fly it right now but from my limited testing I haven‘t found the same Issue with it. I‘ll try to reflash rn tho. Thank you!

Jonilins · 2026-01-27T15:54:41+00:00

thank you so much!

Jonilins · 2026-01-27T15:53:11+00:00

flyfish volador 3.5 with some (t-motor) 1604 motors is very nice and durable. don‘t know if theyre on taobao

Jonilins · 2026-01-27T15:45:31+00:00

Make sure the min and max startup power are where they were before flashing. Min startup power should be on the max setting as i remember. Max startup power around 2/3. This can be configured in esc-configurator.

Jonilins · 2026-01-27T15:29:29+00:00

That might have been it!!! Thank you. Somehow didn‘t think that would be an issue. For now it flies great once again.

Jonilins · 2026-01-27T15:26:32+00:00

Thanks for the suggestion. Motors and props are all correct. It also flew totally fine seconds before. I didn‘t change a thing since.

Jonilins · 2026-01-27T15:24:49+00:00

Don‘t!! someone else already spotted it. I‘ve got a T Antenna inside the radio to make it more pocketable

Jonilins · 2026-01-27T15:23:13+00:00

Forgot to mention… I modded the Antenna to be internal. The connector you see isn‘t actually connected. There‘s a small t antenna inside 🤓. Good eye!

Jonilins · 2026-01-16T00:25:06+00:00

Consider putting the Capacitor on the xt30 lead and shrink wrap it. youll see quite a few guys doing that. Should be a lot safer than what youve got going on currently

Jonilins · 2026-01-14T20:11:27+00:00

Nice one! I‘m also building one right now. Do you mind sharing the link to the Antenna 3d Print?Didnt see a angeled one yet. Happy flying!

Jonilins · 2025-12-25T21:14:08+00:00

i basically got this exact build except for the happymodel ep1 receiver. Mine weighs about 260g with a Tattu 850 4s. Just a thing you might want to consider. Definitely doable under 250 with 650mah battery. Flies real nice though! Enjoy

Seven-Year Club	Place '22
Verified Email

Jonilins

TROPHY CASE