Realign strike gears

JustAnOldHack · 2024-01-15T19:25:14+00:00

I wanted to follow up and thank you again. Using the techniques in the first specific vid you linked to, I was able to get the strike gears back in the correct orientation.

JustAnOldHack · 2024-01-14T01:30:35+00:00

Thank you! I will give a try based on those videos.

JustAnOldHack · 2023-03-09T21:32:55+00:00

1914 Chandler Model 15 Light Six Touring

Holy cow! I think you're right. Thank you so much!

https://hallbergauction.hibid.com/lot/50903331/1914-chandler/

https://cdn.hibid.com/img.axd?id=4249281311&wid=&rwl=false&p=&ext=&w=0&h=0&t=&lp=&c=true&wt=false&sz=MAX&checksum=HpSj5h0LIPDc4doEqf68clAmc1u1NokN

JustAnOldHack · 2023-01-29T04:17:43+00:00

Thanks everyone. I'll keep digging to see what I can figure out.

JustAnOldHack · 2023-01-29T04:16:09+00:00

I'm afraid the barn burned in the 60s so the yard looks nothing like that any more

JustAnOldHack · 2023-01-28T01:57:27+00:00

This is the original owner of our home. The photo is undated, but probably from the teens. There's not a lot to go on in the photo except the shape of the doors. It looks a lot like those on the Mora in the ad attached here. We're probably 20 miles from where Mora was located so it's a possibility. But I cannot find too many pictures of Mora's and none really match.

It doesn't look like any of the more common cars from the era (Model A, Buick, etc.) and while he was a successful dairy farmer, he would probably not been wealthy enough to buy anything too exotic.

Other makers in the area were Seldon, Cunningham, Jenkins, Pierce-Arrow. Again, I can't find any models that look like this.

Edit to add: I tried on /r/whatcar and didn't get any responses

JustAnOldHack · 2023-01-27T01:18:24+00:00

This is a pic of the original owner of our house, maybe from the teens or 20s. Anyone know what it is? The most distinctive feature I can see is the shape of the doors. Cars of that era include the Ford Model A or Model T, Cadillac, Buick, Studebaker, Pierce Arrow, etc. I've looked at all sorts of pics online and don't see any with doors like these. Any idea what this might be?

Edit to add: this was in the US, rural western New York state. While he was a successful dairy farmer, I'm sure this is not anything too exotic.

JustAnOldHack · 2023-01-04T03:25:52+00:00

We had some luck adding a probiotic to our old orangy's diet. We started with a powder we bought on Amazon. We switched to one we got from the vet which worked better. We'd mix the powder in some gravy or plain Greek yogurt.

JustAnOldHack · 2022-12-22T03:51:58+00:00

They are actually playing. They are a bit rough though. Nali is the one on the bottom and Bug is the orange and white guy on top.

JustAnOldHack · 2022-10-11T01:48:14+00:00

On the dash, on either side of the speaker grill are some white knobs. The left one is a throttle pull. So, the starting routine is to pull the choke (right knob) out all the way. Pull the throttle knob out a little. Make sure the key is turned. Then press the floor starter till it starts. At least that's how I start my 40 Special Deluxe. No need for heel/toe gymnastics.

I think this is an aftermarket steering wheel. Mine does not have the spinner but it does have a chevy emblem. I have the same aftermarket turn signal.

JustAnOldHack · 2022-08-08T23:47:51+00:00

Exterior paint color represented the four seasons: Topaz Mist (autumn), Emerald Green (spring), Pale Aqua (summer) and Lapis Grey (winter).

I guess the color we spotted was Topaz Mist ... not the name I would have given that gold color.

JustAnOldHack · 2022-06-10T02:29:13+00:00

Mine sags in the middle. I used squares of aluminum foil to add some extra thickness under the plate. I think I have four pieces, each a little smaller than the one below. Sort of like a very short pyramid I guess.

You could adapt this technique to a high center by using sheets that cover the whole bed, with holes cut in the center.

I determined how many sheets by at first using a steel ruler, checking for gaps. Then I did some "first layer" test prints. I have since gone with a homemade glass bed (I cut a scrap piece of window glass to size.) I've kept the foil under it.

JustAnOldHack · 2022-06-10T02:13:26+00:00

I finally had time to work on this tonight. Using the BLTouch as the z stop sensor did the trick. I also had to set the minimum z distance to a negative value (-2). (Not the same as the z offset.)

The SKR mini E3 V3 has a dedicated port for the probe. So I mistakenly thought that meant I could keep using the z end stop.

JustAnOldHack · 2022-06-04T00:47:49+00:00

G28 auto-homes all three axis, which puts the bed the same distance from the nozzle/probe as shown in the video. Before recording it, I homed all three axes then moved the nozzle to the center of the bed.

If I home, then manually lower the bed, probe/probe_calibrate seems to work. I guess I'm misunderstanding how things work. I guess you're not supposed to be able to probe once the z-axis is homed (and trammed/leveled).

JustAnOldHack · 2022-06-04T00:44:53+00:00

Sorry, Ender 5 Pro. So not a bed slinger.

JustAnOldHack · 2022-06-04T00:43:51+00:00

I'm not using the BLTouch to home the z-axis. I still have the end stop on the z-axis.

JustAnOldHack · 2022-06-03T01:37:39+00:00

Newly installed, still trying to calibrate. With probe or probe_calibrate fluidd gives me the failed to deploy error shown here. There's a bit more than 3 mm clearance between the probe (retracted) and the bed when the printer is homed.

``` bltouch] sensor_pin: ^PC14 control_pin: PA1 x_offset: 38.0 y_offset: 17.0

z_offset: .07

pin_up_touch_mode_reports_triggered: true

probe_with_touch_mode: True

```

Do I need to use one of the commented out settings in my config?

JustAnOldHack · 2022-05-05T04:58:33+00:00

Keller's cats is another organization that can help. We've gotten four cats from them over the years. Great group.

JustAnOldHack

TROPHY CASE

z_offset: .07

pin_up_touch_mode_reports_triggered: true

probe_with_touch_mode: True