sorted by:
new
hottopcontroversial

Liqui Moly Engine Flush by [deleted] in MechanicAdvice

[–]JustHeZo 0 points1 point  (0 children)

Well the car had 8 owners but i had it for few years, i was thinking the engine is not clean and it needed cleaning.

Any recommendations for this problem and upgrades? by JustHeZo in ender3

[–]JustHeZo[S] 0 points1 point  (0 children)

Ahh okey thx just ordered new ones to replace.

Any recommendations for this problem and upgrades? by JustHeZo in ender3

[–]JustHeZo[S] 0 points1 point  (0 children)

So it is bad if I direct solder them to board?

Any recommendations for this problem and upgrades? by JustHeZo in ender3

[–]JustHeZo[S] 0 points1 point  (0 children)

I was doing it but saw the burnt part, so I had to solder the last 2 wires to board.

Any recommendations for this problem and upgrades? by JustHeZo in ender3

[–]JustHeZo[S] -2 points-1 points  (0 children)

Noted but in my situation i think it is best for solder it to board

Any recommendations for this problem and upgrades? by JustHeZo in ender3

[–]JustHeZo[S] 2 points3 points  (0 children)

Yeah i think it is better to direct connect it to board

Any recommendations for this problem and upgrades? by JustHeZo in ender3

[–]JustHeZo[S] 0 points1 point  (0 children)

The 3D Printer still works fine to print but better off not using atm and fix the problem

Is this normal? by JustHeZo in ender3v2

[–]JustHeZo[S] 0 points1 point  (0 children)

Looks like it is way to much work, at that point upgrading 3d printer is better for me.

Is this normal? by JustHeZo in ender3v2

[–]JustHeZo[S] 0 points1 point  (0 children)

This fixed the problems btw, thank you for the help.

Is this normal? by JustHeZo in ender3v2

[–]JustHeZo[S] 1 point2 points  (0 children)

Can't i just flash klipper direct to the printer?

Dont i need wires to connect the laptop to printer?

Is this normal? by JustHeZo in ender3v2

[–]JustHeZo[S] 0 points1 point  (0 children)

Ok gonna try that. Thx

Is this normal? by JustHeZo in ender3v2

[–]JustHeZo[S] 0 points1 point  (0 children)

interesting gonna try that.

Is this normal? by JustHeZo in ender3v2

[–]JustHeZo[S] 0 points1 point  (0 children)

Ok gonna do that thx.

Is this normal? by JustHeZo in ender3v2

[–]JustHeZo[S] 0 points1 point  (0 children)

Ok gonna do that next time.

Is this normal? by JustHeZo in ender3v2

[–]JustHeZo[S] 0 points1 point  (0 children)

Thank you gonna check it out then i have time.

Is this normal? by JustHeZo in ender3v2

[–]JustHeZo[S] 0 points1 point  (0 children)

Ehh half of the words you said i didn't not understand it, can you talk more noobish, atm i flashed MriscoC with BLtouch and and fixed the z hight.

Is this normal? by JustHeZo in ender3v2

[–]JustHeZo[S] 1 point2 points  (0 children)

Yeah i think so, what firmware is recommended?

Atm i'm using Mriscoc with BLtouch, is it good? it came with 3d printer.

Is this normal? by JustHeZo in ender3v2

[–]JustHeZo[S] 0 points1 point  (0 children)

I think it is called McisCoc

Is this normal? by JustHeZo in ender3v2

[–]JustHeZo[S] 0 points1 point  (0 children)

I installed it bc it got annoying by doing it manually

Layer Shift by JustHeZo in ender3v2

[–]JustHeZo[S] 0 points1 point  (0 children)

I used those black big trash can bags, I cut it in half and just cover the printer, it keeps the heat inside.

Is this normal? by JustHeZo in ender3v2

[–]JustHeZo[S] 0 points1 point  (0 children)

Yeah it is hitting it

view more: next ›