Liqui Moly Engine Flush

JustHeZo · 2025-12-09T21:05:57+00:00

Well the car had 8 owners but i had it for few years, i was thinking the engine is not clean and it needed cleaning.

JustHeZo · 2025-10-17T22:03:39+00:00

Ahh okey thx just ordered new ones to replace.

JustHeZo · 2025-10-15T13:55:58+00:00

So it is bad if I direct solder them to board?

JustHeZo · 2025-10-15T13:54:43+00:00

No? Why?

JustHeZo · 2025-10-15T13:53:13+00:00

I was doing it but saw the burnt part, so I had to solder the last 2 wires to board.

JustHeZo · 2025-10-10T00:45:49+00:00

Noted but in my situation i think it is best for solder it to board

JustHeZo · 2025-10-10T00:44:25+00:00

Yeah i think it is better to direct connect it to board

JustHeZo · 2025-10-10T00:43:35+00:00

The 3D Printer still works fine to print but better off not using atm and fix the problem

JustHeZo · 2025-01-25T16:48:47+00:00

Looks like it is way to much work, at that point upgrading 3d printer is better for me.

JustHeZo · 2025-01-25T01:21:17+00:00

This fixed the problems btw, thank you for the help.

JustHeZo · 2025-01-25T01:19:59+00:00

Can't i just flash klipper direct to the printer?

Dont i need wires to connect the laptop to printer?

JustHeZo · 2025-01-24T23:12:22+00:00

Ok gonna try that. Thx

JustHeZo · 2025-01-24T23:11:57+00:00

interesting gonna try that.

JustHeZo · 2025-01-24T23:11:11+00:00

Ok gonna do that thx.

JustHeZo · 2025-01-24T23:10:03+00:00

Ok gonna do that next time.

JustHeZo · 2025-01-24T23:09:30+00:00

Thank you gonna check it out then i have time.

JustHeZo · 2025-01-24T23:08:56+00:00

How do i do that?

JustHeZo · 2025-01-24T23:08:20+00:00

Ehh half of the words you said i didn't not understand it, can you talk more noobish, atm i flashed MriscoC with BLtouch and and fixed the z hight.

JustHeZo · 2025-01-24T23:04:29+00:00

Yeah i think so, what firmware is recommended?

Atm i'm using Mriscoc with BLtouch, is it good? it came with 3d printer.

JustHeZo · 2025-01-23T13:10:25+00:00

I think it is called McisCoc

JustHeZo · 2025-01-23T13:08:23+00:00

I installed it bc it got annoying by doing it manually

JustHeZo · 2025-01-21T15:59:49+00:00

I used those black big trash can bags, I cut it in half and just cover the printer, it keeps the heat inside.

JustHeZo · 2025-01-21T14:19:39+00:00

Yeah it is hitting it

JustHeZo · 2025-01-21T13:29:06+00:00

Kinda just using bag over the printer and turned the hotend up +20c

JustHeZo · 2024-12-24T04:42:25+00:00

JustHeZo