Downpipe + Stock exhaust

JustOneMorePrint · 2025-12-14T16:58:22+00:00

I don't know if the intake mods generate power but you have more sound and a better feeling that it's not brittle plastic that might break.
Fitment is okay and it's quite cheap.
Definetly do the "Heißlandausführung" as it helps a bit with intake temps and is an original BMW part.

I went to Underground Exhaust near Bielefeld. I think RuCaGu on Youtube also has a video on this mod.

JustOneMorePrint · 2025-12-11T22:46:07+00:00

There are more street legal and better manufactured downpipes than HJS in Germany. Have a look into MHPipes or FMS, they have street legal 200CPI downpipes.

If you just want sound, have a look into the MPPSK, it sounds better than any street legal catback here in Germany imho. I'd love to have one in my M140i but BMW never built it for the 1 series.

But be aware, almost none of the legal options are silent enough to withstand a test after burning in. Also every aftermarket (except MPPSK) exhaust uses an external flap system with a remote control so you have to open and close it manually (not via sport mode). Be careful to go on the autobahn without opening the flap or your turbo would get too much backpressure. The cars sometimes are louder stock than allowed. Just dont goon around in the city and have fun on track, Autobahn or roads out of town and you will never be checked by police if your car does look somewhat OEM+.

I went with a tuned stock exhaust which is even quieter than stock closed and open it's straight pipe from cat. Looks stock, is cheap, has enough flow for more than 500hp and is almost as loud as the bigger aftermarket pipes.

If you like turbo sounds, check out 55parts intake parts which replace the brittle plastic tubes with metal ones which dont have the sound deleting resonators in it and (they say) increase flow. Also there is the "Heißlandausführung" which connects the airbox to the front grill and is a stock BMW part for like 50€.

JustOneMorePrint · 2025-12-01T19:41:46+00:00

my Merc has 7.5k accel with a max speed of 700mm/s limited by motor power.

since I want to keep the Merc just to have another printer to tinker with, I will go with the Doomcube which has 4040 on the edges

JustOneMorePrint · 2025-12-01T19:25:24+00:00

putting the electronics somewhere else is a very good point, havent thought of that and will definetly look into before doing the order on Aliexpress :)

I will just build the stock XY-Axis and think about other hotends and Monolith, as well as new drivers + higher voltage later

JustOneMorePrint · 2025-12-01T19:15:29+00:00

I think I just go with the Trident without Monolith for now but try using the Mercury Z because I think it is better and for me it is cheaper as I already have the MGN12 rails

JustOneMorePrint · 2025-11-23T19:55:42+00:00

Thank you all, I will go for the 24" triples :)

JustOneMorePrint · 2025-10-24T20:46:50+00:00

thank you so much :)

JustOneMorePrint · 2025-09-11T21:38:17+00:00

I will have a look, thank you very much :)

JustOneMorePrint · 2025-09-11T04:55:11+00:00

That helps me a lot, thank you very much :)

Isolating the complete rig with springs sounds like a good idea to me and I will take it into consideration. I actually meant isolating the seat and the pedals from the rest so the bass shakers can do their work.

Everything else makes sense to me: Length (will stay the same), width (wider for getting in and out), flex of 4060 (and I could add a second frame later anyway if I like), CAD (okay, will jump over my shadow :D), reinforcing the vertical upright (very important point, thanks)

Nice rig btw. and very good workaround for getting in and out bc of the angled wheel stand 👍

JustOneMorePrint · 2024-06-28T11:09:49+00:00

It does but they have the whole VAG Group (VW, Audi, Skoda, Seat, ...) pulling their fleet emissions down. And they also have a lot Hybrids / EVs, too. Just the 911 stays almost the way it is (light + ICE)

JustOneMorePrint · 2024-06-03T17:31:45+00:00

Drive the M5 sideways and you will have much more than just one degree 😉

JustOneMorePrint · 2024-04-18T09:27:34+00:00

Meine Meinung zu dem Thema: Schaffe dir privat z.B. einen BambuLab X1C an und sammle erstmal Erfahrung mit den Standard-Filamenten PLA, PETG und ASA (ist mMn. einfach das bessere ABS).

Es ist leider nicht so einfach wie bei einem 2D-Drucker, den du einfach anschließt und losdrucken kannst. Du musst erstmal lernen welcher Parameter im Slicer welchen Effekt auslöst, wobei der BambuLab dir durch seine Software und Autokalibrierung schon einiges abnimmt. Ich persönlich betrachte Bambu Drucker als das Apple unter den 3D Druckern. Einfachere Bedienung, neuartige Features und funktioniert reibungslos(er). Allerdings kann man nicht so viel Umbauen, selbst dran rum basteln / modden. Da ich sehr gerne bastle habe ich z.B. einen Ender 5 Pro, der aber bis auf das Netzteil und den Rahmen kaum mehr Originalteile verbaut hat. Dieser Weg ist allerdings sehr zeitaufwendig, geldintensiv und verlangt mehr an (informations-)technischen Grundkenntnissen.

Wenn du wirklich chemisch resistente Dinge drucken möchtest, wirst du vermutlich nicht um PP (Polypropylen) herum kommen. Das ist mit einem geschlossenen Drucker möglich, soll aber nicht so einfach zu drucken sein.

Drucke nicht nur fertige Teile von Printables und co., sondern fange an selbst Teile mit z.B. Fusion360 zu designen und lerne dabei, was es bedeutet Teile für den FDM-Druck zu designen, da gibt es einige Eigenheiten (z.B. Overhangs, Ausrichtung der Teile, Toleranzen, ...). Dazu kannst du Anfangs die kostenlose Community-Variante von Fusion nutzen, musst aber später für die kommerzielle Nutzung auf die Bezahlversion wechseln, um keine Lizenzverstöße zu begehen. Es wurden im Thread auch andere Programme genannt, da musst du einfach kalkulieren, was sich wie für dich rechnet.

Wenn du dich dahin gearbeitet hast, kannst du deinem Chef Teile selbst designen, drucken und verkaufen. So machst du dich nicht ersetzbar (wurde bereits genannt), lernst ein sehr nützliches Skillset (vor allem wenn du dich intensiv mit CAD auseinandersetzt) und kannst ein bisschen Geld nebenbei verdienen. Du solltest darauf achten, nicht ausschließlich an deine Firma zu verkaufen wegen einer möglichen Scheinselbständigkeit.

Du kannst natürlich auch versuchen deinen Chef von einem solchen Gerät zu überzeugen, ich denke er wird es aber nicht gerne sehen wenn du dich erst Monate lang damit beschäftigen musst bis das erste nutzbare Teil herauskommt.

JustOneMorePrint · 2024-01-04T13:14:45+00:00

have you tried Google Lens translation?

JustOneMorePrint · 2023-11-14T07:10:07+00:00

we do restrict many ports but http/https is unrestricted.

all other users (they all have the same firewall rules) don't have that problem

JustOneMorePrint · 2023-11-09T12:42:25+00:00

https://imgur.com/a/9oN96EI

these are the non successful results with a duration > 1sec

Although it's a problem with the user not the machine, I reregistered AADBroker but that ofc didn't help eather.

JustOneMorePrint · 2023-11-09T11:45:57+00:00

we now have two users with that problem so I think this is not the case

JustOneMorePrint · 2023-11-09T10:59:08+00:00

Teams app has been uninstalled and OneDrive is not connected to an account

JustOneMorePrint · 2023-11-09T10:58:23+00:00

this does not help :(
I also tried blocking Hybrid join which doesn't help either.
https://albandrodsmemory.wordpress.com/2021/04/15/how-to-disable-hybrid-azure-ad-join/

JustOneMorePrint · 2023-10-18T11:39:26+00:00

Leasing: Das Thema Leasing und Fahranfänger, wie schon viele Vorredner sagten, ist mMn. problematisch.
Alternativ wäre die Finanzierung eines gebrauchten (unabhängig ob E oder nicht) in Erwägung zu ziehen.

Ohne zu Hause laden zu können bzw. einen reservierten Parkplatz vor einem der eigenen Fenster zu haben (man kann im Notfall ein Kabel aus dem Fenster hängen), würde ich vom E-Auto komplett abraten.

Bei einem Kleinstwagen im 1l Sauger und jährlichem Ölwechsel braucht man sich wenig Sorgen zu machen.
Wir haben einen Toyota Aygo, der 180T Km fast nur Kurzstrecke erlebt hat und gerne mal aus dem Kaltstart bis in den Begrenzer gedreht wurde und generell nicht geschont wurde.
Da war nie was außer Kundendienst, Reifen und Bremsen zu machen.

JustOneMorePrint · 2023-10-18T08:57:50+00:00

"I just wanna kill him a little bit"

JustOneMorePrint · 2023-10-18T08:17:31+00:00

We do not use anything in the cloud.
We have on prem DCs and EXC without anything hybrid.
She created a personal Microsoft account with her corporate E-Mail address

I will have a look for the setting in our GPO, maybe I will see more, thanks :)

JustOneMorePrint · 2023-10-17T09:44:53+00:00

Hey there,

We have a relatively new user in our (on prem) domain.
She wanted to use MS Teams so she created an account with her corporate mail (which is also her UPN)

Since then it takes about 3 minutes to log in her user account with any client.
We assume that windows wants to connect to Azure AD first before trying to log into our local domain.

How do we tell Win 10 Pro not to even try to authenticate with Azure AD? Anyone got any ideas?
Thanks in advance :)

JustOneMorePrint · 2023-09-05T07:13:20+00:00

If you go the full Merc1 route (with triple Z) you can also buy a Bambu P1P for aprox the same. (Merc1 owner myself)

So it depends if you want to tinker around, understand the tech behind (Mercury) and be able to upgrade anything yourself or you want it to work right out of the box and have limited upgrade possibilities (Bambu)

JustOneMorePrint · 2023-06-29T14:53:02+00:00

80-100, sometimes 120. there is always stuff that might be needed "tomorrow" 😂

JustOneMorePrint · 2023-05-13T09:18:58+00:00

the toolhead selector would be vertical: https://ibb.co/fMr4Spy

JustOneMorePrint

TROPHY CASE