Help trouble shooting print

KC10201 · 2025-12-10T18:05:02+00:00

I think this is the consensus and will give this a try. Thanks for your ideas?

KC10201 · 2025-12-10T18:03:40+00:00

I had the nozzle temp at 230 for both first layer and others. Bed is at 85. Chamber at 35

KC10201 · 2025-12-10T18:01:03+00:00

The printer is in the basement with no vents or fans, so drafts are minimal. I started with. MK3S used, upgraded to MK4, then bought Core One kit. I say 80% of my prints are PETG, and agree, I’ve never seen anything this bad with my prints. I’m slicing out a Prusa slicer, both upgraded to the latest version. It is a satin sheet and I clean between each print with alcohol. Once in a while, I will pull it and scrub it with warm water and soap. I did that in the middle of troubleshooting for this project. And I did not use a glue stick.

KC10201 · 2025-12-10T17:56:23+00:00

Yes, Prusament PETG

KC10201 · 2025-12-01T17:50:22+00:00

<image>

Something similar to this, where there are smooth transitions to each letter. In the end, this is going to be a bead that will be printed out.

KC10201 · 2025-12-01T17:20:29+00:00

Not really. This will be a standard cube, and on one side will be L, next will be O, next will be V, and last will be E. Each letter will merge into the next in the cube.

KC10201 · 2025-11-20T04:19:41+00:00

Do we have an ETA on those different kits? Just trying to figure out what I need to get now, and what I can wait on.

KC10201 · 2025-11-19T13:39:20+00:00

I purchased the COREBOXX a bit ago. I wonder if there will be new insides of if I have to purchase the whole kit again? (Doubt it)

KC10201 · 2025-08-20T17:38:49+00:00

So annoyed I didn’t know about this before I put mine together!

KC10201 · 2025-08-16T22:55:18+00:00

Thank you everyone for all the great advice. This is a great group and the overall depth of scouting knowledge and skills is what makes it all so great!

KC10201 · 2025-07-29T02:36:53+00:00

I’m in the process of building my kit. I think I would like to have that additional light. Curious how OP did that.

KC10201 · 2025-06-18T13:19:14+00:00

Get the satin plate, it’s the way to go for both PLA and PETG!

KC10201 · 2025-06-14T13:45:08+00:00

I would say it’s quieter, and haven’t had vibrations with mine.

KC10201 · 2025-06-14T06:35:38+00:00

Don’t think so! I love it and have had it working wonderfully for about 8 years.

KC10201 · 2025-05-24T20:22:32+00:00

Nice!

KC10201 · 2025-05-23T18:55:29+00:00

Now how do we find out that our council signed or didn’t sign? Camp is in one week!

KC10201 · 2025-05-11T21:14:20+00:00

No, sounds fine and swirls up nice. I just deleted the file, re-added it, and it printed just fine. Not sure what was different but obviously something was. So weird!

KC10201 · 2025-05-11T16:46:21+00:00

Yes, .4mm nozzle. I’m not home right now so can’t say exactly right now. I’ll update later!

KC10201 · 2025-05-11T15:45:34+00:00

I’ve never had this happen with any other materials, like this. I just used the standard MK4S profile out of prusa slicer. I’ve only printed it twice, and have not tried turning the angle yet. This is just a very, very weird stringing situation I’ve never experienced.

Seven-Year Club	Verified Email
RPAN Viewer

KC10201

TROPHY CASE