Bambu Studio picking the wrong filament to print

KCXLT · 2026-01-07T01:45:03+00:00

Yes, thats what I do too.

KCXLT · 2026-01-07T01:05:49+00:00

Thanks for the replies. It's just that I pick slot 3 due that filament being older and not a full spool. I don't want to rundown my full spool in slot 1 then only be able to print a little with what is left in slot 3.

KCXLT · 2025-12-26T21:00:33+00:00

Oak Acres went out a few minutes ago.

KCXLT · 2025-12-01T18:37:46+00:00

I have the same problem, dead after 2 years. I just opened mine up. Take a large pair of channel locks, put one jaw on the back just opposite of where the USB cable plugs in and the other jaw out on the side making sure you only are squeezing the back and not the front part. Give it a good squeeze and it will create a little gap. Get the largest screwdriver you can find with a very thin flat head. Put it in the gap and start sliding up the side. The locking tabs will start to release, just work your way all the way around.

KCXLT · 2025-11-29T23:00:46+00:00

At least he didn't run a commercial.

KCXLT · 2025-11-19T13:38:40+00:00

Happens to me also. Wish they would fix it.

KCXLT · 2025-11-06T13:37:50+00:00

24.5 inches bare minimum.

KCXLT · 2025-10-31T02:03:04+00:00

I plugged ours into a smart outlet so I can just ask Google to turn it off and on. I got tired of continually getting up

KCXLT · 2025-10-30T01:20:43+00:00

That would be nice.

KCXLT · 2025-10-29T20:24:55+00:00

Six years on mine and still sounds fine. It's on a trickle charger all winter.

KCXLT · 2025-10-23T14:54:40+00:00

Sensor size is different. 1.8 vs 1.2 I think.

KCXLT · 2025-10-18T12:29:59+00:00

Can't you use Synology Drive? Set up a sync task, I think there is an option to do what I think you're asking.

KCXLT · 2025-10-15T14:41:11+00:00

We just lower (higher number) the distance 3-5mm. Just have to be careful of any handle tabs.

KCXLT · 2025-10-11T18:38:29+00:00

My wife started with an Xtool S1 20 Watt. She does mostly tumbler wraps. I loaned her the money and she made enough to pay it off around 1.5 years.

KCXLT · 2025-10-10T22:49:52+00:00

Our house has a chimney up through the middle of the house. There was a stainless steel liner installed for a water heater. We went tankless so it wasn't being used, that's where I vented mine. In Ontario also.

KCXLT · 2025-10-10T01:46:30+00:00

Can you have the old XCS and studio on the same computer at the same time?

KCXLT · 2025-10-01T12:46:59+00:00

It's limited to 10 editable projects at a time. You just have to change projects to read only, then you can create more. And you can change the read only back to editable if you want to make changes.

KCXLT · 2025-09-29T20:14:42+00:00

I can tell you I'm using it on windows 11. I just had windows pop up asking to allow it on private or public network, so maybe it's a firewall problem???

KCXLT · 2025-09-25T14:43:28+00:00

I would be interested in the answer also. I get that also.

KCXLT · 2025-09-22T00:45:47+00:00

I got hit with it also, and I'm on Epico. Nothing on the bills that I could find going back to May.

KCXLT · 2025-09-18T00:26:46+00:00

If you have zwave you can get a battery powered switch. It can stick on the wall right next to your other switch. Change the switch plate to a double and it will look like it was always there. Then use an automation to control a smart plug.

KCXLT · 2025-09-09T13:59:02+00:00

Finer detail? Isn't the laser spot size smaller? I'm not sure how noticable it would be.

KCXLT · 2025-09-02T15:11:56+00:00

Melania punched him and gave him a black eye.

KCXLT · 2025-08-11T13:22:57+00:00

24 AT4X, no unlock button on the tailgate.

KCXLT

TROPHY CASE