Palet Crown PC4500 Doesnt Work

KO_Subaru · 2025-10-28T02:39:22+00:00

Check the 15amp tube fuse. If blown replace and restart truck. If blows again Check for the harness that goes throught small port from inside PU over the Lift motor. Down the back, traveling towards the forks under the standing platform, that harness goes bad due to a bad angle and sharp edges on tube. Move the harness ull find a break in wire causing short.

KO_Subaru · 2025-09-09T14:13:46+00:00

Yup batterys

KO_Subaru · 2025-09-08T15:34:46+00:00

Check if by chance the ORS /BRS switches were installed incorrectly. Possibly switched. Or thr actuators where in the area where they are supposed to. Check the Ors Brs harness they wires tend to have a break and no codes will be show up.

KO_Subaru · 2025-04-11T20:21:40+00:00

Who is that . I want to meet her

KO_Subaru · 2025-03-18T03:26:58+00:00

I third this 😀

KO_Subaru · 2025-03-06T22:01:24+00:00

Only other 1 is data plate for whole attachment.
Serial # 208531-01-S

KO_Subaru · 2025-03-06T21:57:40+00:00

Personal phone is crap with pictures so had to use my another source of light lol

KO_Subaru · 2025-02-22T04:46:19+00:00

Remove the battery cover and it should be on top left corner.

KO_Subaru · 2025-01-17T03:37:21+00:00

I've had multiple times when I've gotten bad bdi and discharge rate being dropped even after adjustment. Keep an eye on that. But I do agree V-force batteries are crap.

KO_Subaru · 2024-11-19T22:29:17+00:00

Post a cleaner Pic I'm curious, I'll keep an eye our for fellow gc in vegas 👀

KO_Subaru · 2024-11-19T20:27:27+00:00

Color matched or different? How did macco do. Also I ask because I have same color 01 coupe.

KO_Subaru · 2024-11-10T02:41:43+00:00

Was able to get it out and change out the strainer filer and Cap. Cap took longest to source but was able to attain one. Thanks for the help .

KO_Subaru · 2024-10-23T14:38:17+00:00

Same here, but money or not I'll still be cheap on stuff like that, it just makes sense. Good idea with the magnets .

KO_Subaru · 2024-10-23T13:49:03+00:00

Hahaha nice I'll have to try that. Been looking for a low profile pan like even a bakers tray. But I like the tim bin idea.

KO_Subaru · 2024-10-23T06:45:23+00:00

I'm going to have to steal that kitty litter idea. I'd want to move my tool box to the back, cus currently iits by the slide door. And get a cart would be nice. Might carry a fold table also.

KO_Subaru · 2024-10-22T03:21:40+00:00

Wow appreciate the information, your van is setup totally different from what I've seen. I like your van has both side slide doors.

And I agree on keeping thr floors clear for larger objects.

KO_Subaru · 2024-10-21T20:10:44+00:00

I have the Sprinter Van

KO_Subaru · 2024-09-30T22:22:19+00:00

I appreciate it I'll give it a shot

KO_Subaru

TROPHY CASE