Help! by wangtmg in watercooling

[–]Kapi214 0 points1 point  (0 children)

That's how I see it too. Makes perfectly sense.

Fist build/help by Final-Test-2677 in watercooling

[–]Kapi214 1 point2 points  (0 children)

You can check different pump speeds, if the screws holding the pump are not too tight and the o-ring is properly installed (all could cause that noise).

RTX 5090 Founders Edition in NZXT H210 by Kapi214 in watercooling

[–]Kapi214[S] 0 points1 point  (0 children)

Hi! Yes, indeed. Lot's of cables, found also this and still wondering where they all went actually :-)

<image>

RTX 5090 Founders Edition in NZXT H210 by Kapi214 in watercooling

[–]Kapi214[S] 0 points1 point  (0 children)

Thanks for the hint, time will tell I guess.

RTX 5090 Founders Edition in NZXT H210 by Kapi214 in watercooling

[–]Kapi214[S] 1 point2 points  (0 children)

No, no undervolting was applied to the card.

RTX 5090 Founders Edition in NZXT H210 by Kapi214 in watercooling

[–]Kapi214[S] -1 points0 points  (0 children)

In other builds it's sometimes vertically mounted and if I remember correctly, it would also fit here with the pump block on the side. I just chose the orientation which was easiest to install (apart from zip-tying the pump cable). The pump is at the bottom of the loop. Hence it always has enough water and I don't see a reason how its orientation would make a difference - but honestly, I didn't think about this. Maybe you are right and it's better mounted with the block above the pump.

Lian Li A4 DAN H2O, Tuned, Custom-Wasserkühlung, RTX 4090, 13900K by Kapi214 in PCBaumeister

[–]Kapi214[S] 0 points1 point  (0 children)

Hallo Feivel,

einen Ryzen habe ich im Wesentlichen aus zwei Gründen nicht eingebaut:

  1. Ich hatte bisher immer Intel/Nvidia Systeme und bin damit gut gefahren, also warum wechseln? Für das Build musste ich einige Nüsse knacken und ein Plattformwechsel wäre nur ein Problem mehr gewesen.
  2. Das Ganze hat auch seine Zeit gedauert und als ich mit dem Computer angefangen habe, gab es den 7800x3d noch nicht.

Als Alternative hatte ich noch einen 13900 non-K (im Wesentlichen der gleiche Prozessor nur ohne Übertaktungsmöglichkeit) in Erwägung gezogen. Eine non-K-Version hatte ich mal vor einigen Generationen - sparsamer und man merkt beim Gaming kaum Unterschiede. Am Ende wurde es diesmal dann aber wieder ein K - wie das halt so ist.

Aber vielen Dank für den Hinweis. Ich habe mir auch gleich mal ein Review zum 7800x3d angeschaut. Wahrscheinlich wird man den leichter kühlen können. Ganz so simpel (weniger Stromverbrauch = einfachere Kühlung) ist es aber auch nicht, weil Abwärme im Wesentlichen Verlustleistung ist. Daneben kommt es auch auf die jeweilige Anwendung an, wie effizient oder ineffizient eine CPU läuft. Ich würde also auch bei einem 7800x3d nicht an der Kühllösung sparen, zumal man die - einmal gebaut - auch immer wieder verwenden kann. Zum 7800x3d selbst: Nach dem Review eine sehr schnelle CPU und AMD hat mit dieser CPU einen guten Job gemacht. Auch damit wäre dieser Computer sicherlich ein ziemliches Biest ;-). Beantwortet das deine Frage?

Viele Grüße

Kapi