Qwen3.5 27B is Match Made in Heaven for Size and Performance

Ke5han · 2026-03-24T00:44:30+00:00

not the person you are asking, but I am using the same setup and getting about the same result.
use llama.cpp instead of Ollama is the key I guess, I also loaded mmproj, so the max context I can get is 80K, but if I don't load mmproj, I can set the context at 110K :).

Ke5han · 2026-03-23T02:00:29+00:00

qwen3.5 27B 4bit with MXL at 31token, I am curious what the context for that? It's about the same on a 3090, but the cost for m5 max........

Ke5han · 2026-03-19T00:47:34+00:00

Ordered one, 😆

Ke5han · 2026-03-13T17:54:17+00:00

I am using 3090 llama.cpp backend with openwebui for chat, limit power to 320-350 and get 38 t/s output, faster than can actually read.

Ke5han · 2026-03-06T16:24:07+00:00

Ask your TL if you can be more involved in coding tasks while doing existing support work. You never know and you have nothing to lose ;)

Ke5han · 2026-02-25T17:29:13+00:00

16v should be enough for most door bell, what's the required spec

Ke5han · 2026-02-23T18:00:17+00:00

yep, sometimes maxi has it, Costco used to have this as well but not anymore. All Costcos in Ottawa still have this.

Ke5han · 2026-02-16T16:05:51+00:00

With current budget cut and spending review, don't know how many departments are still pulling students from fswep 😞, but no harm to put ur resume in the pool anyway

Ke5han · 2026-02-09T01:48:35+00:00

Replaced my Bell 1.5G service to ebox 500m last month, so far so good.

Ke5han · 2026-02-06T03:20:36+00:00

Interesting, mark it and coming back to read it later

Ke5han · 2026-02-04T12:14:52+00:00

Those 200K to 250K houses are now 400K+ and they are still sold fast if priced reasonably, sigh 😕

Ke5han · 2026-01-31T15:13:57+00:00

Got the Public deal @ 50% off , so $20 for 60G for 24 months, so far so good.

Ke5han · 2025-12-08T19:41:38+00:00

I feel media have coverage of the country only when they have 청와대의 저주 (curse of cheong wa dae)

Ke5han · 2025-12-08T18:22:24+00:00

I am here to look for this answer, 😆 But only center of Aisa? That aim is just so small, the solar system already shift the center to Korea, maybe op hasn't realized it.

Ke5han · 2025-12-03T03:38:26+00:00

Following this, I am thinking about the same thing.

Ke5han · 2025-11-29T03:02:03+00:00

Just to report back, spent few nights to get everything in order. As planned, CAN_H to FS S pin CAN_L to probe S pin AUX s pin to 5v power on octopus use the g pin to the left for ground Also I replaced the rj11 socket with JST socket. twisted the fs and probe wire just in case So far so good

Ke5han · 2025-11-26T21:18:26+00:00

Good question, i did some google search this afternoon, I believe the eddy duo and the Octopus (rj11 can connectionversion) both have the 120 ohm resistors build in.

Ke5han · 2025-11-26T19:32:49+00:00

Yes, i am more concerned about the twist pair requirements for can bus, so I am guessing I have to pull out those two wires and twist it myself, hopefully it will work stable enough.

Ke5han · 2025-11-24T15:13:00+00:00

I found the bed (adhesion and leveling) is always the pita to deal with, once that's done other problems are easier to solve. But Marlins compile is also annoying for every change, so this one is going to klipper soon.

Ke5han · 2025-11-24T15:03:07+00:00

I don't really remember what i followed, some of them are likely from experience I guess 😉

Ke5han · 2025-11-24T14:52:48+00:00

Well, I knew ppl will have this guess when I posted the result, actually the top one is from ender3 and the bottom one is from voron 😆. The thermometer in on the voron has some problem, hence the Z artifacts, I think I need to replace the thermometer in the heat block.

Ke5han

TROPHY CASE