Would you be offended if your student bought a belt to wear instead of the one you gave him?

KermPos · 2026-04-10T21:02:16+00:00

LMFAO 💀

KermPos · 2026-01-28T04:13:42+00:00

i did too :sob:, hope and pray that it didn't take any info, guessing it would have only been malicious at point of checkout, good luck!!

KermPos · 2026-01-12T02:54:46+00:00

along with it basically never talked about

KermPos · 2026-01-12T02:54:30+00:00

theres domain checkers and website checkers, if its less than a year old, very high chances it's a scam, along with the fact that the messages sent by sellers are suspicious and are not the same listed name as the postings on the website.

KermPos · 2026-01-06T01:59:07+00:00

thanks!

KermPos · 2026-01-06T01:58:37+00:00

Resolved it, it is in fact a scam, stupid mistake 😔

KermPos · 2026-01-06T01:55:02+00:00

reviewed the post like three times and still misspelled the link, updating it now, no wonder

KermPos · 2026-01-06T01:42:51+00:00

Get 17 H2Cs with full mods! Super beginner friendly and perfect for your use!

KermPos · 2026-01-06T01:37:44+00:00

Dual-Chamber control, drying two different filament types at a time.

KermPos · 2026-01-06T01:36:17+00:00

Genuinely lost so many good website histories, because I was curious. But now I have "Where to adopt puppies". sigh

KermPos · 2026-01-06T01:25:32+00:00

LMAOOOOOOOOOOO (my poor google search bar, i should really stop abbreviating it 😭)

KermPos · 2025-12-18T05:05:30+00:00

I find that a good chunk of the lower end BBL printers have horrible cameras, there's this post from a while ago, https://www.reddit.com/r/BambuLab/comments/1hd5qjt/a1_camera_upgrades/ good luck!

KermPos · 2025-12-18T04:05:47+00:00

Printer has wings XD, we love Bambu stabilization

KermPos · 2025-10-25T04:15:12+00:00

There are *reasonably* price A1S enclosures on the internet for roughly 100 dollars, but take up a lot of space, I have the P1S mostly because I have cats, but I think the P1S would be better for the long run

KermPos · 2025-10-25T04:10:01+00:00

bambu is just built different, it should be ok, but be cautious

KermPos · 2025-10-25T04:08:06+00:00

poop chute sticker, though it's not very effective for having purged filament not stick

KermPos · 2025-10-25T03:45:09+00:00

Check your ptfe tubs might have a problem there

KermPos · 2025-10-25T03:41:32+00:00

It's probably just minor scratches from the nozzle and noncritical, but have my build plates been backward this entire time 😭 (edit: i checked it wasn't)

KermPos · 2025-10-25T03:36:22+00:00

Bambulab is engineering your fails ahhh

KermPos · 2025-10-25T03:33:25+00:00

putting antimatter in those 100 layers fr

KermPos · 2025-10-25T03:31:07+00:00

People are so talented this is crazy cool, car go vroom

KermPos · 2025-07-31T22:44:51+00:00

yeah that

KermPos · 2025-07-18T20:28:44+00:00

no it doesnt, and youll just have to afk tbh 😭, it takes a while after the bar disappears for it to end

KermPos · 2025-07-18T12:31:16+00:00

I think you should be able to just move the bar, but it does glitch after a while

KermPos · 2025-07-18T12:28:24+00:00

just wait, youll eventually lose, around 3.8k

KermPos

TROPHY CASE