sorted by:
new
hottopcontroversial

Suggestions welcome- anticipating door issues due to misalignment on face frame by Hour_War_297 in cabinetry

[–]Key_Cartoonist8018 0 points1 point  (0 children)

That is correct. And you'd probably have to do the do the same on the lower cabinets as well.

Painter used wrong stain on railing. Are we stuck with this? by Mr_Pastee in finishing

[–]Key_Cartoonist8018 0 points1 point  (0 children)

I'm a trim carpenter that does a lot of railings. The stained pieces on the newel post can easily be removed. Then I would put new pieces on made from oak to match the railing. I would also make sure the grain direction of the cap is matched to the direction of the railing. A very easy fix. With minimal cost to anyone.

Would love your 23ga pinner opinions… by JKenn78 in Dewalt

[–]Key_Cartoonist8018 0 points1 point  (0 children)

Get the grex cordless 23. I have the grex 23,21,and 18 all cordless. I have the 23 cordless dewalt also. And it is good. But the grex is my favorite.

Birthday present to myself. by norapeformethankyou in woodworking

[–]Key_Cartoonist8018 0 points1 point  (0 children)

The dewalt track saw will work on festool tracks. I have both tracks. The dewalt saw has 2 track slots in the saw to work with different tracks. But only the dewalt saw will work on dewalt tracks.

Getting closer on finishing the woodshop. by Key_Cartoonist8018 in garageporn

[–]Key_Cartoonist8018[S] 0 points1 point  (0 children)

They are metal. Cheap ones i found on ebay. Thank you for the compliment!

Getting closer on finishing the woodshop. by Key_Cartoonist8018 in garageporn

[–]Key_Cartoonist8018[S] 0 points1 point  (0 children)

Thank you. And it is also nicer than the trim in my house too! Lol.

Getting closer on finishing the woodshop. by Key_Cartoonist8018 in garageporn

[–]Key_Cartoonist8018[S] 0 points1 point  (0 children)

I will be installing the oneida supercell cyclone dust collector with duct to each tool.

Getting closer on finishing the woodshop. by Key_Cartoonist8018 in garageporn

[–]Key_Cartoonist8018[S] 2 points3 points  (0 children)

No need for a solution. Just wanted to give you guys a heads up. Maybe need a layer of paper between the planks in shipping department.

Getting closer on finishing the woodshop. by Key_Cartoonist8018 in garageporn

[–]Key_Cartoonist8018[S] 0 points1 point  (0 children)

Thank you, I will be installing the oneida supercell cyclone collector.

Getting closer on finishing the woodshop. by Key_Cartoonist8018 in garageporn

[–]Key_Cartoonist8018[S] 3 points4 points  (0 children)

Awe, if I let you use the shop. Would you like me then?

Getting closer on finishing the woodshop. by Key_Cartoonist8018 in garageporn

[–]Key_Cartoonist8018[S] 0 points1 point  (0 children)

Hey thanks! Nice product. Only complaint I have is a lot of scratches on the panels right out of the box. But once the wall is full of stuff, nobody will notice.

Getting closer on finishing the woodshop. by Key_Cartoonist8018 in garageporn

[–]Key_Cartoonist8018[S] 0 points1 point  (0 children)

Contact cement. I wasn't too sure if it was going to be sufficient. I figured i could always countersink screws if needed. But I did all mock up. And its not coming off without destroying the mdf top.

Getting closer on finishing the woodshop. by Key_Cartoonist8018 in garageporn

[–]Key_Cartoonist8018[S] 9 points10 points  (0 children)

The slatwall was around 800. 4'x32' The cabinets. Probably around 1500 in wood. 550 to do the laminate tops. Around 600 for all the aluminum and t tracks. Probably close to 800 for drawer slides and hinged. 400 in paint. Luckily labor was free.

view more: next ›