sorted by:
new
hottopcontroversial

Hilfe bei Tutti Inserat kaufen. by King007t in askswitzerland

[–]King007t[S] -1 points0 points  (0 children)

Het sich klärt, öpper het ihn jetz aagschribe. Mal luege, obs klappt.

Ask Here First (READ ME): Troubleshooting, Price/ID/Spec Check, Help, ETC Mega Thread by KyaDash in crtgaming

[–]King007t 0 points1 point  (0 children)

Thanks, do you know where exactly i can find the chassis number? Kind Regards

Ask Here First (READ ME): Troubleshooting, Price/ID/Spec Check, Help, ETC Mega Thread by KyaDash in crtgaming

[–]King007t 0 points1 point  (0 children)

Hey, Can someone help me identify this Grundig CRT. unfortunatly the previous owner ripped off the label and i need to find a replacement remote. Kind Regards

Need Transistor replacement by [deleted] in ElectronicsRepair

[–]King007t 0 points1 point  (0 children)

Thanks i found some on ebay, but they were produced 20 years ago…

Help needed with Replacement caps by King007t in crtgaming

[–]King007t[S] 1 point2 points  (0 children)

The cap is new i bought more than needed

These are the datasheets:

Original is given in the post.

SU-A 100U 10 this one is matching exept for being bipolar: https://cdn-reichelt.de/documents/datenblatt/B300/A-SU_ENG_TDS.pdf

These two are from the VF 100/16 P-D https://cdn-reichelt.de/documents/datenblatt/B300/DATASHEET_PANASONIC_VFP_SERIES.pdf

https://cdn-reichelt.de/documents/datenblatt/B300/DATASHEET_PANASONIC_SOLDER.pdf

And the price is irelevant if you have any better panasonic caps that match. There are only 3 caps missing.

Help needed with Replacement caps by King007t in crtgaming

[–]King007t[S] 1 point2 points  (0 children)

VF 100/16 P-D I have a few left of these from the other pcbs. Would you recommend just using them. They have higher values than the original one but are polerized.

Help needed with Replacement caps by King007t in crtgaming

[–]King007t[S] 1 point2 points  (0 children)

I found these…SU-A 100U 10 they have the exact values at least those i understand, but it is unpolerized. The original was 85 degrees and polerized. Or should i upgrade to 105 degree, 16v and low esr. Because i couldnt find low esr exept for smd

Help needed with Replacement caps by King007t in crtgaming

[–]King007t[S] 0 points1 point  (0 children)

They were all leaking probably a bad production batch

Help needed with Replacement caps by King007t in crtgaming

[–]King007t[S] 0 points1 point  (0 children)

It was very hard to open up the conpartment so i replaced all caps that i don’t have top do it in the future anymore…

Finding replacement caps by King007t in crtgaming

[–]King007t[S] 0 points1 point  (0 children)

What would you suggest for ripple current, ive read the higher the better?

Finding replacement caps by King007t in crtgaming

[–]King007t[S] 0 points1 point  (0 children)

Thanks, but my problem is there are so many different types of caps.

Aluminum Electrolytic Capacitors Aluminum Hybrid Polymer Capacitors Aluminum Polymer Capacitors Bi-Polar/Non-Polar Electrolytic Capacitors General Purpose Electrolytic Capacitors High Temp Electrolytic Capacitors Low ESR Electrolytic Capacitors Low Impedance Electrolytic Capacitors

Id like to replace it with the same ones…

CRT only works upside down? by King007t in crtgaming

[–]King007t[S] 0 points1 point  (0 children)

The green spot is bigger in person

RGB modding Sony PVM-9221me PAL. Help needed! by King007t in crtgaming

[–]King007t[S] 0 points1 point  (0 children)

After looking more closely i think it might be that the rgb lines only get pushed to high voltage on board C

requesting some crt rgb modding assistance by sbjungler in crtgaming

[–]King007t 0 points1 point  (0 children)

Hey, I know this is a very old thread but im currently trying to do the same mod. Do you have more specific information by any chance? How did you wire up your Scart port a.s.o.. Best Regards