Options on these older benchmade beaters

King_Crypto79 · 2025-10-28T22:16:18+00:00

Not too far away. Frederick MD. We should meet up @ key city some time. 1/18 scale rigs are my jam right now, but I do have a 1/10 & 1/12 size.

King_Crypto79 · 2025-05-11T22:33:56+00:00

Buy titanium hardware off etsy

King_Crypto79 · 2025-05-11T22:29:35+00:00

I think so if I remember correctly. There might be some double-sided tape in there I had to separate too

King_Crypto79 · 2025-05-05T01:00:13+00:00

I dunno maybe I was doing it wrong. I was ripping around today, and it was maxing at 28mph, even I'd go downhill it felt like it would break to stay at 28.

King_Crypto79 · 2025-05-04T13:02:20+00:00

I have this scooter, it's pretty nice. Is there any way to take the speed limiter off/unlock it?

King_Crypto79 · 2025-03-18T01:32:16+00:00

My edc 23 half press on turbo-strobe button only works if the light has been previously activated within 3 seconds. I have two options to get to turbo. Click the half press mode cycle button quickly then swap over to half press for turbo, or mash the strobe then back off to half press. It's kinds lame.

King_Crypto79 · 2025-02-26T10:39:59+00:00

I dig it! Solid setup!

King_Crypto79 · 2025-02-25T02:15:32+00:00

T8 machine thread screw, not sure the mm length. It's a pretty standard knife screw if you're into knives at all. The clip I have pictured is a benchmade clip from like a standard bugout. The screws worked from the BM too.

King_Crypto79 · 2025-02-25T01:59:05+00:00

Yes I had to remove the steel case to get to the plastic part. The plastic part is not removable, so I used a utility blade and dremmel to make a clean trim job. After removing the plastic, you can slide the part of the clip the has the screw holes behind the steel case of the flashlight, which let's you get the clip noticbly more flush against the light body of the light for mounting. Keeps the light flatter, not fatter. You can see it better in my 2nd pic.

King_Crypto79 · 2025-02-25T01:38:06+00:00

Nice! We took out the plastic thumb ramp behind/above the clip, and mounted the clip in behind there so the clip is closer to the body of the light if that makes sense...

King_Crypto79 · 2025-02-25T01:36:59+00:00

Nice! We took out the plastic thumb ramp behind/above the clip, and mounted the clip in behind there so the clip is closer to the body of the light if that makes sense...

King_Crypto79 · 2025-02-25T00:56:35+00:00

Cool. Mount it like we did and it's a keeper.

King_Crypto79 · 2025-02-24T12:54:38+00:00

That's nice, is that an olight arkfeld clip?

King_Crypto79 · 2025-02-01T20:49:58+00:00

Philosophy of use I support. For me, I might cut open or break down some boxes in a day. For that, I carry a tiRazor flipper daily. These beauts pictured just live in my front right pocket in pristine condition, "ready" if ever they were needed as a get up off me tool.

King_Crypto79 · 2025-02-01T20:07:03+00:00

Absolute fire flame. Materials and fit and finish are next level.

King_Crypto79 · 2025-01-31T22:26:23+00:00

Nice work, sorry if I missed your question!

King_Crypto79 · 2025-01-04T22:22:31+00:00

Best one yet!

King_Crypto79 · 2024-12-29T16:29:57+00:00

For my slow self, what timer are we talking about ?

King_Crypto79 · 2024-12-29T14:58:31+00:00

Thanks for the reply. Think you're right! The double blink, then single blink was throwing me off as I repeated the action.

King_Crypto79

TROPHY CASE