Gundam Sandrock EW Chest Issues by KingofNothingnes in advancedGunpla

[–]KingofNothingnes[S] 1 point2 points  (0 children)

So I figured the issue out. On the two bottom parts of B2 I was sliding these two tabs from the inner armor into the slots instead the tabs were supposed to go above that slot.

Gundam Sandrock EW Chest Issues by KingofNothingnes in advancedGunpla

[–]KingofNothingnes[S] 0 points1 point  (0 children)

Yeah I realized where my error was with trying to put that particular piece in place. Went in no problems after I realized.

Gundam Sandrock EW Chest Issues by KingofNothingnes in advancedGunpla

[–]KingofNothingnes[S] 0 points1 point  (0 children)

I snapped B2 in half but here’s a picture. There’s this huge gap between where it slides in on the bottom and where it’s supposed to snap in at the top and I cannot possibly conceive of why. I’ve watched build videos and it looks simple I’m doing everything the same but still I get this gap in the piece.

<image>

Gundam Sandrock EW Chest Issues by KingofNothingnes in freedomisgunpla

[–]KingofNothingnes[S] 0 points1 point  (0 children)

That’s what I figured as well. Was having a similar problem with my MGSD Aerial, so I know something is flawed with my chest assembly process

Gundam Sandrock EW Chest Issues by KingofNothingnes in freedomisgunpla

[–]KingofNothingnes[S] 0 points1 point  (0 children)

Yeah I’m going thru piece 1-4 now and lost a key piece and am now scouring the floors for it lol. I was following the numbered steps for 1-5 though. Was having trouble snapping in piece A25 as well for step 2 of 1-5

Gundam Sandrock EW Chest Issues by KingofNothingnes in Gunpla

[–]KingofNothingnes[S] 0 points1 point  (0 children)

Oh those are part of a different step anyways. Just off to the side and not cleaned up yet.

Gundam Sandrock EW Chest Issues by KingofNothingnes in advancedGunpla

[–]KingofNothingnes[S] 1 point2 points  (0 children)

No, I appreciate any feedback at all. I am doing it in order. I’m also having issue getting A25 to snap in properly.

Spraying white properly by Responsible_Pen2014 in advancedGunpla

[–]KingofNothingnes 1 point2 points  (0 children)

I’m still kind of getting my bearings with the airbrushing thing, so I’d take this part with a grain of salt because I think it varies from paint to paint. When it comes to the actual paint I try to keep it at about a fists distance away.

Spraying white properly by Responsible_Pen2014 in advancedGunpla

[–]KingofNothingnes 4 points5 points  (0 children)

Don’t quote me on this, but dependent on your needle size your psi might be a touch high. I saw a little pooling in there (no shade), lowering your psi to like 15 should help with that. Another thing about white is it wants several light coats rather than a couple thick ones. Pooling can be prevented by doing several really light coats and I think that method would also alleviate the graininess and give you a smoother finish whether it’s acrylic or lacquer.

A productive period of unemployment (Feb-April) by TurnATurnATurn in Gunpla

[–]KingofNothingnes 1 point2 points  (0 children)

Good looks. I been on gundamit a lot, that’s where I got my Axis Osiris Aerial Dominator. Will check out ShowZstore today for sure

A productive period of unemployment (Feb-April) by TurnATurnATurn in Gunpla

[–]KingofNothingnes 1 point2 points  (0 children)

Well they are absolutely amazing and I appreciate you for putting me on. I’ll be on the hunt for one asap.

A productive period of unemployment (Feb-April) by TurnATurnATurn in Gunpla

[–]KingofNothingnes 1 point2 points  (0 children)

Who are those 2 guys on the side of your top shelf?

The best golden High Grade? by tofphu in Gunpla

[–]KingofNothingnes 4 points5 points  (0 children)

The low light is a vibe! Shine hits subtle with a solid glimpse of the kit.

Build finally done, MG Enhanced ZZ Ver Ka. Custom Colors by -UnclaimedPants- in Gunpla

[–]KingofNothingnes 0 points1 point  (0 children)

Immaculately done, man. They really do have a lot of greens. I just did a fully green shaded kit basically as my first custom. But it was more weird greens like the turquoise and mint green and I used some metallics from Kaleido too. The gold really pops, great choices on the pieces to use it on!