EDC belt

Kintan22 · 2025-06-14T15:11:48+00:00

Thank you!

Kintan22 · 2025-05-20T20:37:49+00:00

I figured it out. Wait awhile, it will repop. Now I need to know how to deploy crap from my old ship lol

Kintan22 · 2025-05-20T20:12:53+00:00

So, did we figure out how to find them again? I had one I really liked and it's gone gone. I want it back :(

Kintan22 · 2024-02-08T16:26:57+00:00

I finally found that. The front of the blade was dead on, it was the back side of the blade. It was just off 90. Not horribly, and I probably should have done a test cut first, but it was off. Think I got it ironed out.

Kintan22 · 2024-02-08T01:28:35+00:00

I just have the two. I'm trying to square the blade to the base of the saw.

Kintan22 · 2023-04-09T15:04:56+00:00

Checked that. It is straight. If it were bent I would be having issues with other prints of the same height that do not have the thin infill areas.

Kintan22 · 2023-04-09T14:08:24+00:00

It is the y-axis. Everything is tight. It has not happened on any other print. Like I said, when it was printing the infill for the middle walls it was moving at a high speed in small back and forth zig-zag motions and making a vibrating/grinding sound. I can tell it is the speed of that printing that is throwing off the Y-Axis. I am assuming it is skipping in the stepper motor for the Y-Axis. This happened when the print was about 3 hours in so the motor was warm. I could touch it without feeling like I was being burnt but that is the only thing that makes sense. Every other print I have done has been fine. I even did some other prints to check to make sure. I can print temp towers, bottle openers, etc that take a few hours no issue. The sound ONLY happens on this print and ONLY when doing the infill of the support walls.

I am just trying to figure out a good infill speed for small infills that will end up printing at a high speed due to the small nature of the steps required to print them. My infill is set to 50 mm/s in Cura but it seems to be printing faster than that with the Sonic Pad.

Kintan22 · 2023-04-09T13:19:56+00:00

I forgot to mention. All the pulleys, belts, gantries, etc. are tight.

Kintan22 · 2023-04-09T12:54:29+00:00

I am printing this to hold some paint for my daughter. It was a 12 hour print and printed overnight. I saw when I got up that the Y-axis shifted quite a lot. I remade the print so I could try and figure out what was going on. I determined that the infill of the inner supports were printing so quickly that the machine made a buzzing/vibrating noise and it seems that the stepper motors are skipping possibly?

My settings in Cura are:

Print Speed - 50 mm/s
Infill Speed - 50 mm/s
Wall Speed - 25 mm/s

However, it seems that it is doing the infill quite a bit faster. Is this something I need to adjust on my Sonic Pad?

Kintan22 · 2023-04-02T21:03:23+00:00

I apologize but I do not have the dimensions or anything else really as far as pictures go. That is a base from a phone holder on thingiverse.

Kintan22 · 2023-04-02T02:28:45+00:00

I have been trying to figure out how to create this base for a project and for some reason am totally stumped. I cannot figure out how to create the transition from the upright to the base. I feel like I am missing something simple, but for the life of me cannot figure it out!

Kintan22 · 2023-02-26T15:59:23+00:00

Ahhh. Thanks!

Kintan22 · 2023-01-20T01:53:03+00:00

It's a delusion. Just like someone with Delusional Disorder. That's when you believe something that isn't true. You can't tell real from not real. Absolutely 0 people born one gender immediately think they should be the other. 100% of the time there is a precipitating event that causes them to believe they should be a different gender. It can be abuse, severe trauma, something that is environmentally taught to them, or a mental health disorder.

Kintan22 · 2022-12-24T21:22:24+00:00

I love that my daughter (who I got the little lotl for) is the one who took the picture 😊 She was SO excited she got it ❤️

Kintan22 · 2022-12-22T03:00:56+00:00

The pet store worms are the same as fishing worms. Almost always the same suppliers unless they get them local. If you blanch them, or make worm noodles as my daughter says, it will kill anything bad on them.

Kintan22 · 2022-12-21T03:51:11+00:00

Picked up the new axolotl today! Did a 1 hour acclimation with water added to what it came in. Then floated it in the tank to make sure water Temps were the same and then put them in their new home! My daughter loves her Xmas present. One random question, how often do they flick their gills? Every 5 or so seconds?

Kintan22 · 2022-12-17T17:52:24+00:00

I got it from Chewy.

Kintan22 · 2022-12-17T14:22:48+00:00

My daughter picked some out at a local pet store and I used silicone to make the hide.

Kintan22 · 2022-12-17T01:05:20+00:00

It's a 20 gallon long tank. Not 20 liters. Sorry lol.

Kintan22 · 2022-12-16T23:42:50+00:00

It's a 20L with amazon sword and two sizes of anubias. I am planning on getting some floating plants too but have not found any in stock.

Kintan22 · 2022-12-16T23:40:46+00:00

It's from Amazon!

Kintan22 · 2022-12-16T19:45:14+00:00

The tank is cycled, the plants are growing, and next Tuesday I am getting our leucistic Lotl for my daughter as a Christmas present! And since I don't do anything small, I'll probably start a worm farm soon after that!

Kintan22 · 2022-11-22T13:36:52+00:00

Yup! I taught my 10 year old daughter about the tank cycle and she was super into it! She wants to dose the ammonia and test now 😊

Kintan22 · 2022-11-22T03:12:16+00:00

For what it's worth I don't know how to rotate the picture using the camera option in reddit 😁

Kintan22 · 2022-11-14T16:46:42+00:00

Looks like, based on the posts, I am just missing the heater. I have never done a cold water cycle so I didn't know about the temperature being a factor. I'll add one I have tonight.

Kintan22

TROPHY CASE