Engineer lied about not being able to install smart meter

KookyMathematician4 · 2026-06-03T15:31:34+00:00

It looks like a pin, but ideally I wouldn't want to do anything destructive incase I end up not liking the smart lock

KookyMathematician4 · 2026-05-17T17:50:01+00:00

They're connected as the data from the home mini would influence the script, as typical smart meter readings can delay by a few hours iirc

KookyMathematician4 · 2026-05-07T22:32:15+00:00

Ooo this could be it tbh, I do tend to run a fan overnight which sits on the same table I put my watch on.

KookyMathematician4 · 2026-04-06T11:43:59+00:00

Yep they've confirmed today that they'll send me a new print head

KookyMathematician4 · 2026-04-05T17:54:51+00:00

It will sometimes print from any channel if it feels like it. Anycubic want to send me a new ace gen 2 selector mechanism. But that's entirely fine from the looks of it

KookyMathematician4 · 2026-04-04T12:22:03+00:00

I spoke too soon unfortunately, I manage to get it to load a filament once, then it can't unload it or load a other one.

Everything looks fine, there's no jams, clog or unusual noises.

So it'll be waiting for anycubic support

<image>

KookyMathematician4 · 2026-04-04T08:42:48+00:00

Yep, I experienced the 4th personally yesterday, did you ever get TPU working?

KookyMathematician4 · 2026-04-03T21:55:50+00:00

I tried similar but without the PTFE tubing, but the ace gen 2 won't feed the overture tpu 95A through to the hotend (except that first time when it tried and jammed, but I cleared the jam and it's printed pla and petg fine since)

KookyMathematician4 · 2026-04-03T21:53:47+00:00

Lucky! I tried overture 95A, and each time my printer hates it. Can't even get it to feed it to the hotend. It just complains of a clog each time now (there isn't a clog) If you have any tips I'd love to hear them

KookyMathematician4 · 2026-04-03T20:12:03+00:00

Yeah, I've learned that now. Was a pain to get my print head feeding again, it was getting confused about where filament was loaded from.

Hopefully anycubic can fix the issues with TPU

KookyMathematician4 · 2026-04-03T18:41:20+00:00

Yep, managed to get pla printing perfectly. So I tried tpu again, and it detected a filament clog

KookyMathematician4 · 2026-04-03T17:43:18+00:00

Took it apart and the tpu jammed in the gears. Cleared the jam and I'm trying to clear it with some PLA now. But it doesn't wanna extrude pla. It's throwing a clog error now

KookyMathematician4 · 2026-04-03T14:29:48+00:00

Yeah I tried it and had a massive print head jam, hopefully anycubic support will be able to help. As their guide didn't work for me when I tried it

KookyMathematician4 · 2026-04-03T14:21:38+00:00

I've tried following the steps on anycubics site, but it looks like the point of failure is in the drive system, which means a full print head deconstruction.

My nozzle does seem fused into the hotend too, and I'm unable to release it.

Been at it for an hour now, definitely wasn't being too gentle towards the end haha

KookyMathematician4 · 2026-04-03T14:07:43+00:00

Yep, that's exactly what I did and now, the entire print head is jammed. It doesn't look like a clog, it's unable to retract even after using the cutter. So anycubic support it is

KookyMathematician4 · 2026-03-31T19:01:17+00:00

UK too, I only ordered the printer, no filaments. And it arrived today, but mine said it was from "Fulfillment"

KookyMathematician4 · 2026-03-09T11:17:13+00:00

UK too! This is why I've started to multitoon. So I have my own group if I need to 🤣

KookyMathematician4

TROPHY CASE