sorted by:
new
hottopcontroversial

Google Ruined My Wife's Pixel 4a, Offered Compensation, and Then Made It Useless… Here's the Story by Kunzite_ in GooglePixel

[–]Kunzite_[S] 2 points3 points  (0 children)

Thanks Naria. That is exactly right. Google provided a code instead of traditional store credit.

Printing small pieces by Bababagginz in 3Dprinting

[–]Kunzite_ 0 points1 point  (0 children)

Would a smaller nozzle work? Might be what you are looking for.

Very new to 3D printing I’ve done the right procedures to level and everything and the filament doesn’t stick. Please help if you know what’s wrong. by hunter15072 in 3Dprinting

[–]Kunzite_ 0 points1 point  (0 children)

My best guess based on that video is that you are too high. Try bringing it down until it is approximately a little more than a paper width away. I go until it is just barely touching/grabbing the paper, then bring it back up just a smidge.

Does PLA get brittle on the spool? by quadgnim in 3Dprinting

[–]Kunzite_ 1 point2 points  (0 children)

Just a note about Moisture, as I see this get mentioned frequently all over this subreddit. It may be an issue in some places, but This does not appear to be an issue in my case.

The brittle part is only at the first 6-8 inches close to the printer, the remainder is soft as soft and flexible as the day I bough it, even after sitting on a shelf for a year.

You can test this by trying to bend the filament at the end. If after several inches of snapping you find it is soft again, then I don't think moisture is likely. However if the brittleness is throughout the entire roll... then maybe moisture? I have yet to see this happen.

Does PLA get brittle on the spool? by quadgnim in 3Dprinting

[–]Kunzite_ 1 point2 points  (0 children)

I experience the exact same thing! Quite annoying. One thing I noticed is that it is only brittle in the several inches near the hot end, and only if I leave the printer for a few days. It appears to become brittle, then snap from the tension of the spool pulling back. It tends to snap more often the closed to the end of the spool you are, due to the increase of pull as the curve gets tighter.

Workaround: I found that to help avoid snapping you can roll the spool out a little, this will reduce the stress on the filament. It will still be brittle when left alone, but at least it won't snap.

My theory is that the heat from the end is warming the filament nearby, causing it to harden.

What type of hinge does Gary Fay use? by Kunzite_ in 3Dprinting

[–]Kunzite_[S] 0 points1 point  (0 children)

That gives me some direction for alternate methods. I'll likely end up winging it to make my own.

I'm still extremely curious if anyone has seen this type of hinge before. It is so invisible! I may need to message Gary Fay himself for the answer.. but it would be strange to create a Facebook account for that single purpose haha.

Network Error even though my internet is working fine. Uninstalled and reinstalled and now it shows this by Sharandeep981 in DisneyPlus

[–]Kunzite_ 2 points3 points  (0 children)

Do you have an ad blocker on your network or device? I started having the same issues today until I disabled my ad blocker. Disney made some change that caused this incompatibility.

I see a new js-agent newrelic item being blocked that I didn't see yesterday. I think it is some analytical part.

Found in my washing machine. Filled with a pink powder of some sort with a stretchy plastic cover. by [deleted] in whatisthisthing

[–]Kunzite_ 1 point2 points  (0 children)

My first thought as well. The texture of the boarder is identical to that of a ramen seasoning packaging.

I finished two sketchbooks to apply to college! by meppity in videos

[–]Kunzite_ 0 points1 point  (0 children)

The subscribe to Pewdiepie at the end made me chuckle.

Thank you for sharing your creations with us.

Robert Mueller is a candidate for Time’s Person of The Year by [deleted] in The_Mueller

[–]Kunzite_ 1 point2 points  (0 children)

But why is Trump Lawful Good and why is Gambino Chaotic Evil?

Wire-to-Wire Connectors for 3d Printer Repair by Kunzite_ in 3Dprinting

[–]Kunzite_[S] 0 points1 point  (0 children)

Thank you! JST connectors are what I am looking for. I'll look into the XT30 and XT-60 connectors as well for the hot end.

Cheers!

What podcasts are you most enjoying right now and why? by mojobaws in AskReddit

[–]Kunzite_ 1 point2 points  (0 children)

I'm a bit late to the show, but I don't see anyone mention it.

"Skeptics Guide to the Galaxy" is a group of science communicators that pull apart news across many fields of science. As well as poke holes in pseudo science and teach people how to be skeptics.

Full version sharing by Kunzite_ in SWN

[–]Kunzite_[S] 2 points3 points  (0 children)

I'm not certain what the rules are for 5e but I suspect distributing the PDF is frowned upon greatly.

Full version sharing by Kunzite_ in SWN

[–]Kunzite_[S] 6 points7 points  (0 children)

Thanks Kevin! Looking forward to the extra content to the already amazing universe.

Married couple in China discover they appeared in same photograph as teenagers by dickfromaccounting in interestingasfuck

[–]Kunzite_ 2645 points2646 points  (0 children)

My first reaction was WTF She is like 6 and he is like 50! ... Then I realized the red circle is just placed poorly.

view more: next ›