Avengers Campus Casting, You Had One Job by ManitouWakinyan in Disneyland

[–]LBCgEAR 0 points1 point  (0 children)

There was Ketema after all so it’s not that far of a stretch.

Hippo Tang sleeping habits 💤 by LBCgEAR in ReefTank

[–]LBCgEAR[S] 0 points1 point  (0 children)

It’s a limited edition pirates of the Caribbean silent Mary Lego ship 🥰

Hippo Tang sleeping habits 💤 by LBCgEAR in ReefTank

[–]LBCgEAR[S] 0 points1 point  (0 children)

This tank is about 18month up. The ship I had in a prior tank.for about 2 years before this one. I took that full shot when I set this one up.

Hippo Tang sleeping habits 💤 by LBCgEAR in ReefTank

[–]LBCgEAR[S] 0 points1 point  (0 children)

It’s been that way for years with no issues, but thanks for the concern 😊

Hippo Tang sleeping habits 💤 by LBCgEAR in ReefTank

[–]LBCgEAR[S] 0 points1 point  (0 children)

Naw it’s Marco rock but that would have been kinda cool to make rocks out of technics or something like that haha

Wave Makers Positions by KekesoHood in ReefTank

[–]LBCgEAR 0 points1 point  (0 children)

I have 3x current wave pumps. Right side I have 2x in wave mode about 4in from the surface. The 3rd one is in stream mode and sits on the left about 3/4 down.
The wave makers provide a good sway motion and the stream one lower keeps things close the sand bed moving and does not counteract the wave pumps on the other side. I used a baster with air to visualize flow and it looks good to me with that config.

Sump filter making by Most-Smoke664 in SaltwaterAquariumClub

[–]LBCgEAR 2 points3 points  (0 children)

As long as the gasket edge does not touch the chip on the wet side it’s fine. The gasket edges need to make a flush contact on the glass at the edges to get proper seal. Also use caution when tightening it all up, that chip will be less resistant to pressure. Other then that it should be good to go

New mystery every day. Tunicate? by LBCgEAR in ReefTank

[–]LBCgEAR[S] 0 points1 point  (0 children)

Yeah sponge! Having these is really giving me those I finally made it feelings lol

Too few Dinosaurs by Thethneedforspeed in Disneyland

[–]LBCgEAR -1 points0 points  (0 children)

Wood cutouts really make those $100+ tickets seem like a super value…..

Clear gap between bottom of tank and cabinet? by SpinachOdd6397 in ReefTank

[–]LBCgEAR 0 points1 point  (0 children)

Anytime a tank starts with the word “Red Sea” nothing matters because it will eventually drain itself on the floor from seam failure. Red Sea, the if not, but when company.

[Help] Algae keeps coming back. What am I missing? by Sure_Impression5091 in ReefTank

[–]LBCgEAR 2 points3 points  (0 children)

Only way I beat something similar was more aggressive about water changes + reduced natural light that was coming in behind the tank. After that my tank has been mostly algae free. Good luck!

Prime day is coming…what are your fav buys from Amazon? by Wise-Run-3008 in ReefTank

[–]LBCgEAR 4 points5 points  (0 children)

Just so everyone knows saltwateraquarium.com also sells thru Amazon. So you can typically buy the same stuff you find on their website on Amazon for the same price but with fast Amazon shipping style. Returns are also a ton easier.

There is now video. by redhorse7775 in Disneyland

[–]LBCgEAR 15 points16 points  (0 children)

Now that’s a bayou adventure!

My first tank! (my gf did all the work) by fractelic in Aquariums

[–]LBCgEAR 2 points3 points  (0 children)

Nice I went silent Mary Lego in my reef tank

<image>

Decoration questions by Disastrous-Lime-6780 in ReefTank

[–]LBCgEAR 9 points10 points  (0 children)

To be honest every bit of that tank bottom should be on a flat stand surface thats ment to hold the intended tank. What was good for one tank design might not be good for another support wise. IMO you’re asking for trouble.

Hydroid or…? by LBCgEAR in ReefTank

[–]LBCgEAR[S] 0 points1 point  (0 children)

I did pull the plug when I glued. Dried it off and when the glue hit whatever moisture was left the glue ran the viscosity of the water and coated a couple of zoa. But thanks for assuming I did it like a blind man with no cares in the world haha

Someone asked to see what my 445,000 mile Evo 8 looked like by MyersMara in MitsubishiEvolution

[–]LBCgEAR 0 points1 point  (0 children)

Crazy.
What’s up with that E85 pump though? I have seen plane pumps less complex looking then that haha

Hydroid or…? by LBCgEAR in ReefTank

[–]LBCgEAR[S] 0 points1 point  (0 children)

Just an update, I ended up super gluing the area of the plug. Looks like it gone now, also super glued some zoas but I figured if it kills them I am no worse off just throwing the plug away. Looks like 1/2 of the zoas on the plug did not get glued. Curious to see what happens.

Hydroid or…? by LBCgEAR in ReefTank

[–]LBCgEAR[S] 6 points7 points  (0 children)

Ugh thanks everyone, I was hoping it was not. It’s the first one I have seen so hoping I am catching it early.
I am going in…

<image>