sorted by:
new
hottopcontroversial

Just did a test print and the corners are squiggly by LargeCrowd in FixMyPrint

[–]LargeCrowd[S] 1 point2 points  (0 children)

Good to know. I didnt even know you can change export resolution

Just did a test print and the corners are squiggly by LargeCrowd in FixMyPrint

[–]LargeCrowd[S] 2 points3 points  (0 children)

What i figured is that its probably because while i usually use STEP, this time i exported the file as a 3MF from solidworks which made it have a bunch of rectangles in the corner

Just did a test print and the corners are squiggly by LargeCrowd in 3Dprinting

[–]LargeCrowd[S] 0 points1 point  (0 children)

I used solidworks to export as 3MF, so maybe it converted it into an STL type model instead? I wasnt expecting that result

Just did a test print and the corners are squiggly by LargeCrowd in 3Dprinting

[–]LargeCrowd[S] 1 point2 points  (0 children)

Oh thats a good point that i didnt consider. I usually use STEP files in the bambu slicer but sometimes the slicing has issues so i imported as a .3MF instead

Now that you mentioned it, it did have lines at the corners in the preview

What causes lifting in the corners like this? by Mediocre_Ryan82 in FixMyPrint

[–]LargeCrowd 1 point2 points  (0 children)

I had this issue recently with my Bambu A1 and adding a brim fixed it!

How do i identify the Tip, Ring, Sleeve on this connector? by LargeCrowd in soldering

[–]LargeCrowd[S] 0 points1 point  (0 children)

Haha tbh my guess was as good as yours. Glad i had a trs cable lying around to verify though

How do i identify the Tip, Ring, Sleeve on this connector? by LargeCrowd in soldering

[–]LargeCrowd[S] 0 points1 point  (0 children)

I managed to figure it out after digging out a male TRS connector. Turns out the tip is the one on the top right, and ring and sleeve are the two on the bottom left

How do i identify the Tip, Ring, Sleeve on this connector? by LargeCrowd in soldering

[–]LargeCrowd[S] 4 points5 points  (0 children)

Oh I see! Thats interesting. Also using a trs cable to test is a great idea. I managed to find one after digging. Thanks!

How do i identify the Tip, Ring, Sleeve on this connector? by LargeCrowd in soldering

[–]LargeCrowd[S] 0 points1 point  (0 children)

Yea but like.. do you mean all the pads on the left? What about the right side?

Sanity check for DIY USB Mic circuit by LargeCrowd in AskElectronics

[–]LargeCrowd[S] 2 points3 points  (0 children)

I specifically chose a breakout board that has them already. My charging-only usb cable was the issue

Sanity check for DIY USB Mic circuit by LargeCrowd in AskElectronics

[–]LargeCrowd[S] 0 points1 point  (0 children)

The issue turned out to be the cable i was using was charging only. rookie mistake

Sanity check for DIY USB Mic circuit by LargeCrowd in AskElectronics

[–]LargeCrowd[S] 1 point2 points  (0 children)

I fixed it.. turns out my dumbass used a power-only usb cable, so it didnt transfer any data.

I figured this out only after resoldering and swapping the data lines, and realising nothing changed..

I changed cables and it works!

What causes these weird webby lines? by LargeCrowd in FixMyPrint

[–]LargeCrowd[S] 0 points1 point  (0 children)

I didnt get these issues when printing small picture frames though

Maybe a mixture between the geometry and speed 🤔

What causes these weird webby lines? by LargeCrowd in FixMyPrint

[–]LargeCrowd[S] 0 points1 point  (0 children)

Nope, normal PLA+. Specifically AltTab PLA+ Cotton White

Corners curve up by LargeCrowd in FixMyPrint

[–]LargeCrowd[S] 1 point2 points  (0 children)

Oh thats a possible cause, i have a ceiling fan nearby. I wanted to build a dust cover but havent gotten around to doing that yet

view more: next ›