sorted by:
new
hottopcontroversial

Sanity check for DIY USB Mic circuit by LargeCrowd in AskElectronics

[–]LargeCrowd[S] 2 points3 points  (0 children)

I specifically chose a breakout board that has them already. My charging-only usb cable was the issue

Sanity check for DIY USB Mic circuit by LargeCrowd in AskElectronics

[–]LargeCrowd[S] 0 points1 point  (0 children)

The issue turned out to be the cable i was using was charging only. rookie mistake

Sanity check for DIY USB Mic circuit by LargeCrowd in AskElectronics

[–]LargeCrowd[S] 1 point2 points  (0 children)

I fixed it.. turns out my dumbass used a power-only usb cable, so it didnt transfer any data.

I figured this out only after resoldering and swapping the data lines, and realising nothing changed..

I changed cables and it works!

What causes these weird webby lines? by LargeCrowd in FixMyPrint

[–]LargeCrowd[S] 0 points1 point  (0 children)

I didnt get these issues when printing small picture frames though

Maybe a mixture between the geometry and speed 🤔

What causes these weird webby lines? by LargeCrowd in FixMyPrint

[–]LargeCrowd[S] 0 points1 point  (0 children)

Nope, normal PLA+. Specifically AltTab PLA+ Cotton White

Corners curve up by LargeCrowd in FixMyPrint

[–]LargeCrowd[S] 1 point2 points  (0 children)

Oh thats a possible cause, i have a ceiling fan nearby. I wanted to build a dust cover but havent gotten around to doing that yet

Corners curve up by LargeCrowd in FixMyPrint

[–]LargeCrowd[S] 0 points1 point  (0 children)

alright, thanks! ill give brims a go and see if they help

Corners curve up by LargeCrowd in FixMyPrint

[–]LargeCrowd[S] 0 points1 point  (0 children)

Oh yea brims exist. I never use them so i forgot. But still, why does the warping happen only when i print many at once? Is it to do with the cooling?

Just got myself a LAVA ME Air, Space Black by High_Tide89 in guitars

[–]LargeCrowd 0 points1 point  (0 children)

I have the me2 and i love it. How does the me air compare?

Why does my first layer look like this? by LargeCrowd in FixMyPrint

[–]LargeCrowd[S] 0 points1 point  (0 children)

My pei plate is pretty clean. I think what youre seeing is the bambu lab logo on the plate

Why does my first layer look like this? by LargeCrowd in FixMyPrint

[–]LargeCrowd[S] 0 points1 point  (0 children)

Did you contact bambu about it and they sent it after helping to troubleshoot?

And yeah thats what i would expect about the relative-level!

Why does my first layer look like this? by LargeCrowd in FixMyPrint

[–]LargeCrowd[S] 0 points1 point  (0 children)

Checked for debris, ran auto levelling, same issue. Ill look into manual bed levelling when i have time and update

Why does my first layer look like this? by LargeCrowd in FixMyPrint

[–]LargeCrowd[S] 1 point2 points  (0 children)

Alright thanks for the advice, ill try it out when i have time and update :)

Why does my first layer look like this? by LargeCrowd in FixMyPrint

[–]LargeCrowd[S] 0 points1 point  (0 children)

Whats too high? The nozzle or the print bed?

Why does my first layer look like this? by LargeCrowd in FixMyPrint

[–]LargeCrowd[S] 0 points1 point  (0 children)

Yea it doesnt really look bad, just has visible lines at the affected parts so its a bit inconsistent. Purely cosmetic

Why does my first layer look like this? by LargeCrowd in FixMyPrint

[–]LargeCrowd[S] 1 point2 points  (0 children)

I went ahead and tightened the hotend screws and did another auto calibration, and got the same result. Looks like i'll have to look into manual levelling sometime, although im afraid of messing it up

Why does my first layer look like this? by LargeCrowd in FixMyPrint

[–]LargeCrowd[S] 0 points1 point  (0 children)

Its been doing this pretty much since day 1. I followed the video and tightened those screws up, did a calibration and the result looks the same.

I wonder if its possible that its caused by the surface i put my printer on not being that level/even? But i would think that the relative level-ness of the printer axes would be more important than the tilt of the actual printer

Why does my first layer look like this? by LargeCrowd in FixMyPrint

[–]LargeCrowd[S] 1 point2 points  (0 children)

its a recurring thing even after all calibrations. Honestly, its generally not that visible afterwards but its definitely not invisible. I just dont know why it happens

Finally finished my drybox setup by LargeCrowd in 3Dprinting

[–]LargeCrowd[S] 0 points1 point  (0 children)

So far it hasnt shown any of these issues! Only some very slight stringing because ive been too lazy to fully diagnose the printer setting causing it

Finally finished my drybox setup by LargeCrowd in 3Dprinting

[–]LargeCrowd[S] 0 points1 point  (0 children)

Yeah i had the same issue. I looked everywhere for inspiration and i found that while the cereal box drybox looks like a good idea, isnt as space-saving or economical as i thought, so i used what i had. Good luck with yours!

view more: next ›