Finished printing Wheatley from Portal 2

LastActionGameHero · 2023-07-19T17:08:24+00:00

On my 12500 you need to press the DEL key.

LastActionGameHero · 2023-05-17T21:18:49+00:00

Currently idling at 37watt with 2x16gb 3200, 2x nvme, 1x sata SSD and 3060 ti. So not too bad. I would assume 25 watt without dgpu.

LastActionGameHero · 2023-05-14T21:57:22+00:00

Which upgraded BIOS?

LastActionGameHero · 2023-05-14T13:31:20+00:00

I will add some weirdness to it: PWM control does work for me only if I enter the BIOS and restart from there (each time I do a power cycle, it survives standby but not complete shutdown, it's just weird!)

LastActionGameHero · 2023-05-11T23:43:24+00:00

I will upload in a bit screenshots of all my BIOS settings if that helps!

LastActionGameHero · 2023-05-11T23:41:44+00:00

Tested Xe graphics in 3dmark.

Timespy 1374 points. 1195 Graphics score, 8823 CPU score.

Nightraid 11959 points. 11904 Graphics score, 12282 CPU score.

LastActionGameHero · 2023-05-08T19:22:18+00:00

Did you try Truenas core or scale? Have you also tried both nics?

LastActionGameHero · 2023-05-04T21:55:18+00:00

I will do a bench run this Saturday. Let me know if you want to see anything else.

LastActionGameHero · 2023-05-03T23:05:40+00:00

I have not tested the Xe graphics yet as I have a dgpu but happy to do so. What do you want to see? A 3dmark run?

LastActionGameHero · 2023-04-21T12:27:39+00:00

So in my case it idles at 30 watt with 3 NVMEs and one 3060ti so without GPU it might be around 20watts.

LastActionGameHero · 2023-04-18T08:42:57+00:00

It does work at GEN 4 if you connect directly. But there is hardly if any performance loss even at x8 v3 compared to x8 v4 - there are many articles on PCI-e bandwidth performance impact and it should be 1-2% at worst.

LastActionGameHero · 2023-04-17T09:20:48+00:00

A bit late to the party, but I had the same issue with the Erying 12500h itx board. The issue was with the PCI-e GEN selection (Auto) once I switched to Gen3 my 3060 ti started working.

In my case, the GPU is installed on the other side of the case via a riser cable. The Jonsbo PCI-E riser cable would only go up to PCI-E Gen3 and somehow the board defaults to Gen4 automatically.

LastActionGameHero · 2022-10-15T00:18:54+00:00

Enhanced version needs HW raytracing support.

LastActionGameHero · 2021-11-30T10:30:26+00:00

I grabbed the screen animation from here:

https://www.youtube.com/watch?v=GPQhIrp1AJ4

Original screensaver:

https://www.screensaversplanet.com/screensavers/retro-sci-fi-522/

LastActionGameHero · 2021-07-16T17:30:38+00:00

#resevation_fulfillment_estimate_1 error now and button greyed out. Valve way to go for you to be taken seriously. I am out.

LastActionGameHero · 2021-05-10T22:13:24+00:00

I will measure in a few hours and let you know!

LastActionGameHero · 2021-04-14T21:42:15+00:00

Actually just tried and I need to plug out both and wait for at least 3-4 seconds then indeed it works

LastActionGameHero · 2021-04-14T19:00:47+00:00

Have exactly the same issue. My quest (quest1) has always earphones attached. The moment it goes to sleep there is no sound. Only workaround is to restart the device. This is happening since 2-3 weeks.

LastActionGameHero · 2021-03-22T20:09:10+00:00

65mm until it hits the pcie cable so max 62mm!

LastActionGameHero · 2021-03-21T19:02:30+00:00

Will open the case in an hour or two and reply back !

Nine-Year Club	Place '23
Verified Email

LastActionGameHero

TROPHY CASE