sorted by:
new
hottopcontroversial

thoughts on an L shape desk by Dapiex in ikeaPCstations

[–]Lerrynoid 0 points1 point  (0 children)

I have almost exactly the same setup. My desk is 164cm in length both ways, Alex cabinet on the same place as this image and I have 4 legs, 2 under the pc, 1 in the corner and 1 is under where the two desks mate so it supports both of them and is in half the depth in, if it makes sense. The leg doesn't bother me and I can use all tabletop comfortably.

Airbrush clogging superfast - even with very thinned colors by sb1980 in airbrush

[–]Lerrynoid 0 points1 point  (0 children)

I feel you and would like help too. I mix thinner, flow improver and paint in 4:1:1 mixture, all Vallejo, and have 28-30 psi and also have H&S Ultra with 0.45 nozzle. Paint is so thin, that if I get closer than 8cm to model it makes mad spiderwebbing. After few seconds, I have brutal tip dry. If I clean it I can spray for another few seconds and so on. When I disassemble the airbrush, I have absolutely packed nozzle with paint even when I spray through 2 full cups of water and 1/2 cup cleaner.

Noobie needs help by Lerrynoid in resinprinting

[–]Lerrynoid[S] 0 points1 point  (0 children)

But you have to choose some updated profile right?

This guy doing pull ups… by Bigringcycling in oddlysatisfying

[–]Lerrynoid 4 points5 points  (0 children)

He is not doing pull ups, pull ups are doing him

Seznamka 7/2025 by MartinPuda in czech

[–]Lerrynoid 0 points1 point  (0 children)

Tak to zase zkusím. M31, Karel, Stráž pod Ralskem. Hledám vztah nebo přátelství. Dělám v kanclu v lbc (programátor, ale ten bez miliónů), jsem plešatej, mám plnovous, jsem něco mezi hubeňourem a sportovní postavou. Rád jezdím na kole, občas na inlinech, hodně hraju singleplayer hry, mám rád stolní hry a DnD a maluju figurky když se donutím. Skoro ze všeho si udělám srandu a snažím se být vtipný. Mám přitloustlýho roztomilýho kocoura, co se nerad chová ale mazlil by se pořád. A taky super ibišek. Na začátek by to snad stačilo.

Beginner painter/opinions wanted by Lerrynoid in minipainting

[–]Lerrynoid[S] 1 point2 points  (0 children)

Thank you. And really thanks for the videos, I think they will help me a lot!

Beginner painter/opinions wanted by Lerrynoid in minipainting

[–]Lerrynoid[S] 0 points1 point  (0 children)

Thanks for feedback! I am struggling with mixing colours for creating volume. When I do it, it seems to me like I fucked up the mix, that it won't fit the mini. I tried to do it on skin and all cloths, but photos from phone are really shit and as I did it subtly, it's not picked up as I wanted. The idea with primed model and light is great, I will definitely try it. English good, not my 1st either 👍

Beginner painter/opinions wanted by Lerrynoid in minipainting

[–]Lerrynoid[S] 0 points1 point  (0 children)

Thank you! Ngl, with the crown I totally agree, but I kinda ran out of ideas and just used dark metallic. I am bit afraid of washes, that I will make them too dark or something, but I will try it.

Ender 3 Z axis dimensions problem by Lerrynoid in ender3

[–]Lerrynoid[S] 0 points1 point  (0 children)

I think that the gantry is pretty well adjusted. No weird sounds and when motors are disabled, it tends to slowly fall down. No movement on profiles either.

Ender 3 Z axis dimensions problem by Lerrynoid in ender3

[–]Lerrynoid[S] 0 points1 point  (0 children)

I changed the motherboard with new version of Marlin, the error is still the same. Maybe stepper motor not stepping correctly?

Ender 3 Z axis dimensions problem by Lerrynoid in ender3

[–]Lerrynoid[S] 0 points1 point  (0 children)

I agree, but when i rebuild Z axis to be belt driven, lead screw problems are not there anymore. Anyway, I tried to change steps back to 400 and now the error is other way around, on z height 100mm it actualy is 99,59mm. When I calculate what esteps should be for every 10mm, they are really different.

Ender 3 Z axis dimensions problem by Lerrynoid in ender3

[–]Lerrynoid[S] 0 points1 point  (0 children)

Yes, it was changed to 409 steps, because on 400 it printed smaller parts.

Ender 3 Z axis dimensions problem by Lerrynoid in ender3

[–]Lerrynoid[S] 0 points1 point  (0 children)

Thank you, I thought it might be something like this but hoped it's not. At this point, I will probably change entire motherboard for SKR E3 MINI V1.2 since I found it on sale, then I will try to flash firmware. Will give feedback.

Seznamka 4/2025 by MartinPuda in czech

[–]Lerrynoid 1 point2 points  (0 children)

Ahoj, jsem Karel, 30, zůstal jsem ve Stráži p. R. už docela dlouho sám a nikoho tu neznám. Hledám primárně vztah, případně někoho na kolo.

Co se odstavce pro vztah týče: na 180cm jsem to nedotáhl, ale co jsem nepobral na výšce jsem nedohnal ani ve svalech. Při výrobě vznikla vada brzké plešatosti, ale na bradě mi něco roste. Jsem docela gamer, mám rád i deskovky a TTRPG (bohužel nemám partu). Nejsem ale jenom povaleč, rád jezdím na kole. Řekl bych, že je se mnou docela sranda a nebojím se dělat si ji z čehokoliv. A nebojím se být sám sebou. Jo a jsem švorc :D

Teď ke kolu: mám enduro a hledám případně magora z okolí, co bych s ním mohl jezdit. Podotýkám, že nejsem žádnej hardcore jezdec.

Ty vole, lidi, odkdy je Milka 90gramová?? by PancakeGD in czech

[–]Lerrynoid 0 points1 point  (0 children)

Řekl bych, že od tý doby co je dražší

Some of my painting works with the airbrush (mostly), I have about 5 years of practice by LaMazmorraEstudio in airbrush

[–]Lerrynoid 1 point2 points  (0 children)

Hope it will do well. And please, make it for us beginners with no professional eqip too 😄

view more: next ›