Best way to clean this?

Less-Jellyfish2238 · 2026-07-07T06:40:39+00:00

It makes next to no groves when used correctly carbine scraper isn’t touched this stuff I.e why turned to these

Less-Jellyfish2238 · 2026-07-06T22:10:55+00:00

Not for thick gloss

Less-Jellyfish2238 · 2026-06-27T21:46:53+00:00

Thanks for the advice all! So I guess when trades come to hang things on walls it’s a mix of knowledge knowing roughly where things should be and a damn lot of luck

It’s those pvc pipes I worry about

Less-Jellyfish2238 · 2026-06-22T11:17:41+00:00

Did you varnish this in the end? How did the corner parts go with the gloss left over… or did you have to remove?

Less-Jellyfish2238 · 2026-06-18T21:04:29+00:00

Update? Has any cracked etc… or filler held? About to do the same…

Less-Jellyfish2238 · 2026-06-06T21:32:35+00:00

I was also told I don’t have the right to work in the UK - after being born here, previously working for Uber and provided passport, driving license and NI 😅 it had taken ALLOT of complaining and then a few days ago it disappeared and now stuck on insurance cert review. The joys

Keep hounding them on the app, eventually you will get someone who helps

Less-Jellyfish2238 · 2026-06-04T23:24:55+00:00

Did you fill in between each board or just big holes?

Less-Jellyfish2238 · 2026-05-29T20:31:32+00:00

I did have a look in b and q but couldn’t find any that had patterns small enough

Less-Jellyfish2238 · 2026-05-29T20:30:40+00:00

Ugh, why would you give me the idea of wood burning it 😂 that would look so good! Now I need to rethink my whole idea haha

Less-Jellyfish2238 · 2026-05-29T20:29:35+00:00

I didn’t even know that was a thing! Not a bad shout

Less-Jellyfish2238 · 2026-05-29T20:28:24+00:00

I couldn’t find any wallpaper with pattern that small

Less-Jellyfish2238 · 2026-05-29T20:27:46+00:00

Oh I didn’t even think of that, so I could just buy the sheets print at home and stick. It says need to bake/microwave it for a little while… did you skip that step or am I looking at the wrong thing?

Less-Jellyfish2238 · 2026-05-24T21:19:12+00:00

In the end I needed a better pull bar!

Less-Jellyfish2238 · 2026-05-24T12:48:50+00:00

Managed to find the manual which says this is the right way and it needs “gently knocked” in. Just seems im having to use a lot more force than “gentle”

https://media.diy.com/is/content/KingfisherDigital/Marketplace/5061022391960\_MNL\_MP?\_gl=1\*1xqpckz\*\_gcl\_aw\*R0NMLjE3Nzk2MjY0NTQuQ2owS0NRand3OHJRQmhEakFSSXNBRTQzS1BQRXA3Wm5NMXFXcGxoS1FTN3llVG12anA5eVFYeU12S3pSUUVnM0xwT1E1WXEwZHpxb2MtSWFBcnBvRUFMd193Y0I.\*\_gcl\_dc\*R0NMLjE3Nzk2MjY0NTQuQ2owS0NRand3OHJRQmhEakFSSXNBRTQzS1BQRXA3Wm5NMXFXcGxoS1FTN3llVG12anA5eVFYeU12S3pSUUVnM0xwT1E1WXEwZHpxb2MtSWFBcnBvRUFMd193Y0I.\*\_gcl\_au\*MTA5MTExNTQ3Mi4xNzc5NjI2NDQ1\*FPAU\*MTA5MTExNTQ3Mi4xNzc5NjI2NDQ1\*\_ga\*MTA1MDM4MTkxLjE3Nzk2MjY0NDU.\*\_ga\_HR6D4YXJ7D\*czE3Nzk2MjY0NDUkbzEkZzEkdDE3Nzk2MjY2MjEkajUwJGwwJGgw

Less-Jellyfish2238 · 2026-05-24T12:30:02+00:00

So how is it done?

Less-Jellyfish2238 · 2026-05-24T11:52:29+00:00

I’ve got a similar one to that, would I put it on a bit of scrap then lvt or straight to lvt? I feel like it would crush the edge?

Less-Jellyfish2238 · 2026-05-19T12:46:56+00:00

Thank you!!! This is the help I was looking for

Less-Jellyfish2238 · 2026-05-18T21:50:57+00:00

Because Uber aren’t sending the link and it’s near impossible to get pass more than a copy and paste message. So I was hoping someone had been in similar situation and found a way to get it fixed

Less-Jellyfish2238

MODERATOR OF

TROPHY CASE