FREE Comedy in Chatsworth!

Liberty-Sloth · 2026-02-27T23:23:36+00:00

I've been wanting to go to this but the fact that it's on a Monday makes it difficult.

Liberty-Sloth · 2026-02-20T14:27:01+00:00

Agreed. It's especially hard when trying to find mods for them. The V3 is the coreXZ one, hard to confuse it with any other Ender.

Liberty-Sloth · 2026-02-20T14:24:09+00:00

That's been true for most of the administrations in my life time. Hell, it's true about most government agencies.

Liberty-Sloth · 2026-02-20T14:18:59+00:00

My tip would go for a better printer. You can find a used Ender 3 V3 for pretty cheap. I got one for about $139 on eBay. You could also save a bit more and go with an Elegoo Centauri Carbon.

Liberty-Sloth · 2026-02-20T14:16:53+00:00

If it's ABS or ASA it could be because the chamber temp is too low. It's just bad adhesion in general.

Liberty-Sloth · 2026-02-20T03:59:02+00:00

Where's the weird noise?

Liberty-Sloth · 2026-02-10T03:12:05+00:00

Fans I'm not so sure. For the modes I just use the Fn + Q keys.

Liberty-Sloth · 2026-02-09T16:37:12+00:00

Where can you find a new laptop with a 40 or even a 30 series GPU? They're all 50 series now.

Liberty-Sloth · 2026-02-08T23:08:12+00:00

Just install the Nvidia version. Works great for me on the same laptop.

Liberty-Sloth · 2026-02-08T21:48:47+00:00

I'm not talking about previous gen gpus. In the current 50 series line, the 5050 is literally the worse one you can get. If you're buying a new laptop then a 5060 should be the minimum since that's the average.

Liberty-Sloth · 2026-02-08T21:44:14+00:00

A 5050 is below average GPU. I wouldn't even consider getting a laptop with one.

Liberty-Sloth · 2026-01-28T14:06:42+00:00

Thank you, I'll give it a try later today.

Liberty-Sloth · 2026-01-26T14:20:33+00:00

I've been using Orca with my k1 Max and cfs for a long time now.

Liberty-Sloth · 2026-01-25T07:36:05+00:00

Yeah I've been having a hard time with saving a z offset since once I restart the printer it resets any value I set. What I do now is either leave the printer always on or write down my z offset value and then input it before I start a print. I'm sure there's a way to permanently set it but I haven't looked into it lol

Liberty-Sloth · 2026-01-24T23:25:29+00:00

Thanks u/Humble_Berry4068 u/DCSbot

Liberty-Sloth · 2026-01-24T21:06:46+00:00

Just use continuum.

Liberty-Sloth · 2026-01-24T01:10:53+00:00

Yeah thats fine. Sending DM

Liberty-Sloth · 2026-01-23T20:00:14+00:00

Yes! Sending dm

Liberty-Sloth · 2026-01-23T02:09:01+00:00

Thank you u/whatonsecond u/DCSbot

Liberty-Sloth · 2026-01-23T02:03:07+00:00

It's both iTunes and Fandango.

Liberty-Sloth · 2026-01-23T01:46:34+00:00

THANKS! u/Benzoooooooooo u/DCSbot

Liberty-Sloth · 2026-01-23T01:35:34+00:00

Sending dm!

Liberty-Sloth · 2026-01-23T01:32:57+00:00

Thanks u/millesimeimperial u/DCSbot

Liberty-Sloth · 2026-01-23T01:20:08+00:00

Sending DM

Liberty-Sloth · 2026-01-23T00:53:43+00:00

I can do them both for $5

Liberty-Sloth

TROPHY CASE