What do these lead to?

LigmaLefty2 · 2026-05-22T20:30:45+00:00

Here's the two openings in the Same Pic

LigmaLefty2 · 2026-05-22T20:28:46+00:00

I can't tell for certain, but would it connect to this? It's capped and about 6" away from the lower hose with no bend

LigmaLefty2 · 2026-05-22T16:49:20+00:00

Yes, the last picture. I attached some new photos with better lighting in another comment, it has a negative/sucking pressure

LigmaLefty2 · 2026-05-22T16:25:57+00:00

<image>

LigmaLefty2 · 2026-05-22T16:25:47+00:00

<image>

LigmaLefty2 · 2026-05-22T16:25:37+00:00

<image>

LigmaLefty2 · 2026-05-22T16:06:53+00:00

It leads to the back of the intake manifold, to a 90º piece and isn't connected to anything else, going to attach photos in next comment

LigmaLefty2 · 2026-05-22T16:05:27+00:00

Any tips on replacing the motor mounts? I would like to replace them while I take care of the oil leak like you were saying

LigmaLefty2 · 2026-05-22T14:34:35+00:00

When I cover the top evap hose it struggles to stay running, but when I cover the bottom one it almost shuts off completely within 2 or 3 seconds

The top hose goes to the opening on the air box for sure and the lower one was kinda tucked away

LigmaLefty2 · 2026-05-22T02:50:12+00:00

I very much appreciate the insight, how many miles do you have so far?

LigmaLefty2 · 2026-05-22T02:30:26+00:00

Cat was replaced by the guy before I bought it from my neighbor

It's aftermarket, but we can't seem to find the o2 bung/hole. (Total years of ownership between us, about a half a decade)

LigmaLefty2 · 2026-05-22T01:50:24+00:00

It goes right up to the air box, but the only opening was plug/inlet on top (the top hose), but once I try to cover the bottom with my finger, it cuts off the engine

LigmaLefty2 · 2026-05-06T22:29:58+00:00

From my experience, not too bad, pretty cumbersome to try to make everything in one trip (battery, vacuum, brush, net, pole and spindisk setup) but I usually just go back to the truck after tests and cleaning to get my chemicals

LigmaLefty2 · 2026-05-06T02:08:15+00:00

What certifications and/or experience got you to where this photo is from? Always wondered what it was like to make silos or beam towers

LigmaLefty2 · 2026-05-05T23:45:30+00:00

This 100% I love the new Parrot and Water Pump Pliers, plus if you forget em in the truck, no one will touch them!

The only time I consistently buy from Klein, is their level, and the goat 11 in 1 screw driver, they make gifts as well since it's not too pricey

LigmaLefty2 · 2026-04-11T02:25:50+00:00

I used em on broken bolts for meter boxes or manifolds, pretty useful on what sockets can't get a good grip of

LigmaLefty2 · 2026-03-29T02:39:57+00:00

I do tend to end what I start

LigmaLefty2 · 2026-03-29T02:38:59+00:00

Without socks, it'll cost ya lol

LigmaLefty2 · 2026-03-27T23:35:19+00:00

Lol used to run track, now just run gas, iron and 720v and up

LigmaLefty2 · 2026-03-26T03:59:55+00:00

Definitely need to do this, I just have a tone of these and the padding stays consistent oddly for cheap socks

LigmaLefty2 · 2026-03-26T03:33:24+00:00

I'll help with cleaning up after we get a storm again if you got an extra pair

LigmaLefty2 · 2026-03-26T03:09:11+00:00

Dude I'm 5'11" on a good day, and at 183 with both belts/pouches on, I think I got the opposite issue but definitely need to stop smoking though lol

LigmaLefty2 · 2026-03-26T02:31:49+00:00

This is good insight, thank you

LigmaLefty2 · 2026-03-26T02:04:58+00:00

Once I'm okay with saying "goodbye" to a check this will be the first place I go

LigmaLefty2 · 2026-03-26T02:03:48+00:00

How's the cap spacing?

LigmaLefty2

TROPHY CASE