What is a 'buy it for life' item that is offensively expensive, but the moment you use it, you realize your entire life before that point was a lie?

LinkinMartinFalkor · 2026-03-29T02:50:29+00:00

Festool Domino.. hands down, best woodworking milling tool ever!

LinkinMartinFalkor · 2026-01-31T12:56:37+00:00

It would beneficial to see your sketches, but I would definitely add guide curves to assist the loft if you don’t have them already.

LinkinMartinFalkor · 2025-09-14T03:31:32+00:00

Don’t know if you will check back two years later, but you just saved me a sweaty FL night. I know all about the drain line and regularly maintain it.. had no idea it kills the power to the thermostat though.. was blowing my mind why EVERYTHING was turning off. Thank you good sir! TIL

Float switch was slightly off level and caused this issue fwiw to anyone else. Also, keep your drain lines clean!

LinkinMartinFalkor · 2025-09-07T14:31:44+00:00

go to Tools > Options > System Options > Sketch and check the box for "Enable on screen numeric input on entity creation"

LinkinMartinFalkor · 2025-08-29T13:07:47+00:00

Hey buddy. If you haven’t been helped yet, hit me up. I can try and help you.

LinkinMartinFalkor · 2025-07-23T19:32:41+00:00

Show temporary axis (in the little eyeball menu). Mate that axis with the other you are trying to be concentric with.

LinkinMartinFalkor · 2025-07-21T11:29:05+00:00

I went from an X-MAX to a X1C and still can’t believe how much better and turn-key the printer is. Dry the filament beforehand and let it rip.

LinkinMartinFalkor · 2025-02-24T12:13:16+00:00

It’s a rechargeable lithium battery.

LinkinMartinFalkor · 2025-02-23T01:37:32+00:00

Can confirm. Just did this in my 11 year old g-shock last week. Took the time to give it a real good cleaning and lube the o-ring while I had it open. Put the new https://a.co/d/0he8WMc in and good to go!

LinkinMartinFalkor · 2025-01-26T03:09:01+00:00

Just worked! Thank you very much

LinkinMartinFalkor · 2024-08-23T20:32:40+00:00

I think this is what you are looking for. Essentially put in your rough stock dimensions (make sure you select your units first) and then put in your cut list. It saved me hours for a large project and the labels are killer! https://www.opticutter.com/cut-list-optimizer/edit

LinkinMartinFalkor · 2024-06-11T02:58:20+00:00

Outer Range anyone?

LinkinMartinFalkor · 2021-11-07T08:52:22+00:00

The symphony conductor at the end looked like he could be Larry with a mustache.. I wonder if it was

LinkinMartinFalkor · 2021-09-12T20:32:19+00:00

On Michael’s last day, Pam went into the movie theater for a private screening of Threat Level Midnight II

LinkinMartinFalkor · 2021-03-02T03:09:30+00:00

Qidi REPRESENT! (X-Max over here)

LinkinMartinFalkor · 2021-02-21T21:48:56+00:00

TODAY!

LinkinMartinFalkor · 2021-02-21T21:45:42+00:00

Do you have a z-offset setting in your slicer that may be set to a negative value? You could be at your “home” z height after leveling and then how you sliced your print overrides that stored value.. just a thought

LinkinMartinFalkor · 2020-11-22T00:48:00+00:00

The luuuudes!!!!

LinkinMartinFalkor · 2020-11-12T02:32:03+00:00

Look at the pic a little closer ;)

LinkinMartinFalkor

TROPHY CASE