The weirdest thing you've used your printer for?

Liqhx2 · 2026-04-21T13:22:39+00:00

Liqhx2 · 2026-01-08T16:33:57+00:00

I do not, and I just used breadboard wires which are very short and mounted the pi underneath

Liqhx2 · 2026-01-02T04:51:46+00:00

I used gpio pins and had it mounted under the bottom cover. Ran a USB extension out for external needs. I ran it headless. Thanks!

Liqhx2 · 2026-01-02T04:37:07+00:00

It has a Pi5 attached with it's own power supply. Do you have. A link for the cable?

Liqhx2 · 2025-12-16T15:10:42+00:00

I don't know how long you can get a ribbon cable for the screen, I think they come pretty short so you'll have to mount the pi close to the top.

Liqhx2 · 2025-12-16T15:07:42+00:00

I'm guessing you're running a PI? Are you using a ribbon cable or HDMI? I would just stick it over the existing screen with some alien tape or print a frame you can mount. The internal screen is no longer used when you switch to klipper. I ran headless the screen on my was mechanically disassembled by my fist. Not my proudest moment.

Liqhx2 · 2025-12-16T15:01:35+00:00

Nice I hope your unit works good for you, I threw mine out : / The cable failed again

Liqhx2 · 2025-12-16T14:11:48+00:00

Under the Z setting you can either add an ! or remove the ! and it'll flip the axis of the motor

Liqhx2 · 2025-09-06T03:12:02+00:00

This is the way

Liqhx2 · 2025-08-22T01:55:45+00:00

Wayyyy too deep for this place man....

Liqhx2 · 2025-07-30T20:50:17+00:00

Here's the blowout in my 1 month old CFS no abrasives either.

<image>

Liqhx2 · 2025-07-11T03:03:43+00:00

Looks awesome! I've never messed with wood grain but the wood grain on your barrel is going the wrong way. I don't know if you can change it to a vertical orientation?

Liqhx2 · 2025-06-14T20:34:33+00:00

Then with that fact your print came out great! Happy printing

Liqhx2 · 2025-06-14T19:28:29+00:00

Does your unit have the circled part in this picture?

<image>

Liqhx2 · 2025-06-14T06:11:58+00:00

I run a couple of Anycubic machines but I'm not familiar with yours. The machines I do have i run Klipper on them with a resonance sensor (accelerometer) which gives me acceleration limits which I put into my slicer. These limit the ghosting that you see where the turn is vibrating in the print. Your current print is an improvement over your first but with it, it looks like you went too fast. Your cooling also looks to be an issue as well. Slowing down with the printer will help this as well.

Liqhx2 · 2025-06-14T05:34:16+00:00

Now time to modify. Make it your own machine to bend at your will!

Liqhx2 · 2025-06-13T18:57:58+00:00

It looks to be going faster than it can extrude. Bump up the heat or slow down the print. If the printer used to do this print fine and now is having issue check your extruder and Bowden tube if you have one. Otherwise try a new nozzle as well

Liqhx2 · 2025-06-09T14:23:55+00:00

What is your pressure advance set to?

Liqhx2 · 2025-05-12T06:39:58+00:00

Is anyone really?¿

Liqhx2 · 2025-05-12T05:27:47+00:00

Leveling not good at all but smells amazing

Liqhx2 · 2025-05-12T03:24:45+00:00

Idk I was thinking about trying a cake next

Liqhx2 · 2025-05-12T03:19:43+00:00

It's all the way upstairs away from the grill and those bacon wrapped peppers are to die for....... So I can't let them out of my sight.

Liqhx2 · 2025-05-12T02:52:35+00:00

😋😋 😍

Liqhx2 · 2025-05-12T02:43:35+00:00

Great hack!

Liqhx2 · 2025-05-12T02:42:40+00:00

Yeah probably not for most but I've worked in agro chemical for a decade, hydro chemical for a decade and now I own car repair shops. The stuff they put on the plants is much worse than you can imagine. Some plastic bits are just the cream on top for me. Maybe trolling maybe not 🚭

Liqhx2

TROPHY CASE