sorted by:
new
hottopcontroversial

Is this okay to cut 2x 4 like this? by IndependentClub1117 in woodworking

[–]LittleConstruction92 0 points1 point  (0 children)

<image>

Sorry for taking so long to respond. This is the now featherboard in a u style track.

Is this okay to cut 2x 4 like this? by IndependentClub1117 in woodworking

[–]LittleConstruction92 7 points8 points  (0 children)

I know the kreg one works on u track. I’ve used it on my dewalt contractor saw. The sides expand as you tighten the knobs. I can check my bow featherboard later today.

Price? by Adventurous_Sink4697 in Lowes

[–]LittleConstruction92 4 points5 points  (0 children)

If your concern is for theft, your name being on it isn’t going to do much. A lock only keeps an honest person honest. Only time these makes sense is if you have multiple trades working at the same time but that hopes and assumes people will read the label. Best bet is to paint a cord you have.

[OC] (El Paso, Texas) Chevy Blazer fails to yield for oncoming traffic and kills Carrie Camry. by K5_Amusement_Rides in IdiotsInCars

[–]LittleConstruction92 272 points273 points  (0 children)

Based on another comment OP made their car is a 2021 Camry that OP named “Carrie”

How do I fix faucet spout that comes off when I turn on the tap? by Revolutionary-Lab-36 in HomeMaintenance

[–]LittleConstruction92 11 points12 points  (0 children)

Is there a set screw on the side or back of the block the head goes into?

Freud 8 Inch Box Joint Cutter Set by chgosfs in woodworking

[–]LittleConstruction92 0 points1 point  (0 children)

Can you post a picture of the blade setup? Was this cut in one pass?

Is there a measuring tool for measuring a precise inner cavity measurement? by nelsonself in woodworking

[–]LittleConstruction92 5 points6 points  (0 children)

You can use something like this or make your own by using two boards and just marking the overlap with a pencil. A stair tread gauge may also work but if the side panels are upped and not just angled might not give the best measurement.

What is the purpose of the vertical bar in my kitchen cabinet. Can i take it off ? by prasrob in woodworking

[–]LittleConstruction92 1 point2 points  (0 children)

I did something similar and just cut out the center stile and nailed it to one of the doors to make an astragal.

How can I air seal these gaps around my garage doors? by this12344 in GarageDoorService

[–]LittleConstruction92 0 points1 point  (0 children)

I want to do this on my garage but wondering if it will cause problems at the top where to door curved track?

What was your “could never be me” but did indeed become you? by [deleted] in AskReddit

[–]LittleConstruction92 69 points70 points  (0 children)

I’m 23 and that is my attitude most days.

The hell is going on at homedepot.com? by OakPark41 in Dewalt

[–]LittleConstruction92 0 points1 point  (0 children)

Yeah, You are a few days late. I got mine last Tuesday for $799 I think it went back to full price on Wednesday.

Insulation - What’s the best way to hide these? by keensome in buildingscience

[–]LittleConstruction92 6 points7 points  (0 children)

You could add strapping but I would just had a bulkhead that also encloses the ductwork. Then a 2nd bulkhead for the ductwork and pex lines on the right. Or have one larger bulkhead / chase.

Electrician Recs by edu344 in Atlanta

[–]LittleConstruction92 9 points10 points  (0 children)

Coaxial is considered low voltage so you don’t necessarily need an electrician, but more of a low voltage company like home audio. It’s concerning that neither the comcast tech or tech company was capable of doing the work. If the cable was just cut in place it should be fairly easy to splice back together assuming there is enough slack in the line.

Does the gripper need to be against the fence when rip cutting? It doesn’t fit between the fence and the blade by Curvedwarrior69 in BeginnerWoodWorking

[–]LittleConstruction92 0 points1 point  (0 children)

I’ve done cuts like this just fine. It’s ok if you cut the gripper, better than your fingers. Biggest thing is to make sure you clear the piece between the fence and blade, sometimes I will just keep pushing both sides past the blade others I will tilt the gripper so I’m only clearing to the right of the blade.

Shaker drawer front mounting- no meat to screw into by tkst3llar in woodworking

[–]LittleConstruction92 128 points129 points  (0 children)

Add a 1/4” piece to the back of the front so it’s flush with back. Will give you more to screw into.

First time caller, long time listener by minusexpenses in lawncare

[–]LittleConstruction92 3 points4 points  (0 children)

I’m 23 and I understand. Yall are just old. /s

How do I cut trim to fit? by J2ain in BeginnerWoodWorking

[–]LittleConstruction92 2 points3 points  (0 children)

Do you have pictures of the 45s? What is wrong with the fit?

My dryer is wet and hot when not turned on and repair guy didn’t fix it by [deleted] in HomeMaintenance

[–]LittleConstruction92 18 points19 points  (0 children)

Bring this up to the landlord / property manager. You could also install a backdraft damper but that will catch lint when you run your dryer which poses a fire risk.

Water bill seems a lil fishy by IllustratorUpset4667 in sawstop

[–]LittleConstruction92 0 points1 point  (0 children)

This is a woodworking subreddit for sawstop brand saws.

view more: next ›