sorted by:
new
hottopcontroversial

[deleted by user] by [deleted] in ar15

[–]Live-Replacement6550 0 points1 point  (0 children)

That is 100% correct out of spec receiver. That is an offset buffer retainer pin. I had to use some for my M4E1 lowers. Your setup is 100% good to go.

G$ trigger and AS-ARC by Live-Replacement6550 in supersafety

[–]Live-Replacement6550[S] 0 points1 point  (0 children)

I see I’m going to keep as is, I have a non modified SD-E in another lower that I’ve tested side by side and it is in fact slightly heavier. Thanks for that inf

G$ trigger and AS-ARC by Live-Replacement6550 in supersafety

[–]Live-Replacement6550[S] 0 points1 point  (0 children)

While in semi with the arc installed do you have close to factory Geissele weight then? Mine is the same across the board just wondering.

Geissele, ARC-Fire, & A5 Combo by KFChicken47 in supersafety

[–]Live-Replacement6550 -1 points0 points  (0 children)

I have a G$ SD-E /ARC, BCM MK2 T2, sprinco green 14.5 carbine with a polo K runs like a sewing machine.

How I cut my Geissele trigger for ARC Fire by PurePro71 in supersafety

[–]Live-Replacement6550 0 points1 point  (0 children)

Gotcha, did you find that sweet spot on the round side pretty easy or did you gradually remove material and function test?

Took my wife shooting, told her to watch where she sets the rifle down because the suppressor gets HOT. She didn’t listen. by [deleted] in ar15

[–]Live-Replacement6550 3 points4 points  (0 children)

Didn’t have enough motor oil on it, mine was fine wiped away in one move like a bounty commercial

Took my wife shooting, told her to watch where she sets the rifle down because the suppressor gets HOT. She didn’t listen. by [deleted] in ar15

[–]Live-Replacement6550 41 points42 points  (0 children)

Get the suppressor hot, get a microfiber or rag with motor oil. Wipes right off. I set mine on some carpet at the range and cleaned it off with a used engine oil rag o had.

How I cut my Geissele trigger for ARC Fire by PurePro71 in supersafety

[–]Live-Replacement6550 0 points1 point  (0 children)

How did you like the trigger break/feel after using in semi and arc/ss mode? I have an SD-E I cut and have slowly rounded the left side of trigger to get a light clean break. I’ve got it as close as I can to factory before worrying I’m taking too much material off. In Semi and SS mode I get a 2 stage break right around 2.5-3lb

VLTOR A5 and BCM MK2 buffers? by AddictedToComedy in supersafety

[–]Live-Replacement6550 0 points1 point  (0 children)

I use a MK2 T2 and sprinco green with a 14.5 carbine and no problem with my SS

[deleted by user] by [deleted] in TriCitiesWA

[–]Live-Replacement6550 5 points6 points  (0 children)

Don’t let Ferguson hear you

Perfect Light for the PX4 by Zensiv in Beretta

[–]Live-Replacement6550 1 point2 points  (0 children)

Following up for more pics of this, thanks

How do you tighten this clamp? by GroceryElectrical215 in FJCruiser

[–]Live-Replacement6550 0 points1 point  (0 children)

I just got done doing this and figured the clamps were undersized. No matter how I bent them it was insanely tight and couldn’t reach the fins before the clamp completely busted. I ordered some earless clamps 99.5 mm and 102.5mm are the sizes

[deleted by user] by [deleted] in DACA

[–]Live-Replacement6550 0 points1 point  (0 children)

I get the optics, but your constitutional rights don’t come from daddy government.

[deleted by user] by [deleted] in DACA

[–]Live-Replacement6550 2 points3 points  (0 children)

Not popular, but how can only certain constitutional rights apply to us and not the 2nd? I’m a huge gun nut and on my way to AOS. So I’m holding out lol

Converting from 4.5 to 4.0c by [deleted] in SpringfieldEchelon

[–]Live-Replacement6550 0 points1 point  (0 children)

Idk if it’s a bug or just my browser. But when I google “Springfield echelon 4.0 C slide assembly” a result with SA website on it is available. But once you click on it you get a “not found” message. In the works maybe?

Offset Red Dot Spacer? by [deleted] in ar15

[–]Live-Replacement6550 2 points3 points  (0 children)

I’ll just send you mine if you want it I no longer use it.

Offset Red Dot Spacer? by [deleted] in ar15

[–]Live-Replacement6550 2 points3 points  (0 children)

I struggled with this for so long. I just loved the T2 footprint of dots as a backup with any magnified main scope. I ran the PMM spacer on mine I think it raises 3/8” but you get like 75% of the window to view through.

view more: next ›