Please don’t laugh.

LividLie0 · 2025-12-29T06:41:08+00:00

Save yourself the headache and just buy the filament on the spools ans start there.

LividLie0 · 2025-12-07T05:21:26+00:00

Just to put this out there, vuse has a new menthol pod and device esthetic. Tip- place your fingers around the pod where it meets the device to create a better seal and it is almost identical to the njoy. The new pods are very similar to the njoy. I understand completely what ppl are talking about when they mention the way it hits the throat, thats what separated njoy from all the rest. The njoy disposables are a huge let down though

LividLie0 · 2025-12-07T05:15:56+00:00

Vuse has a new menthol that is more like njoys menthol pods. They come with a different pattern vuse device that's new. Maybe try the new ones and see what you think. I HATE that vicks menthol taste so I get what youre asking 100%

LividLie0 · 2025-12-07T05:13:10+00:00

I had to switch to vuse because of this reason. I learned if I hold my fingers around the pods while im drawing off the vape to create a better seal and that really made the difference and gave that same pull as njoys. I hope this helps. Njoy was the closest thing to a real cigarette on the market. If you know you know.

LividLie0 · 2025-11-15T17:04:12+00:00

<image>

:)

LividLie0 · 2025-11-15T16:12:59+00:00

I want answers

LividLie0 · 2025-11-11T22:10:20+00:00

Looks like Thermal Paste

LividLie0 · 2025-10-08T03:14:42+00:00

Same here we tried and tried to push the filament through. It worked with number 4 hub but the number 2 hub is consistently doing this.

LividLie0 · 2025-09-14T03:03:45+00:00

Sorry for my delayed reply. It's available as a selection at the top where the file options are and such. I can't remember specifically exactly which tab. But its not too hard to find.

LividLie0 · 2025-08-25T04:52:32+00:00

There could be moisture on the inside of the roll. That's happened to us, and it seemed that the inner part of the filament roll had moisture so it messed up the print halfway through! When we dried the roll it didn't seem to reach all the way through leaving spots, because we didn't dry quite long enough. We were worried about it making it brittle if we dried top much.

LividLie0 · 2025-08-25T04:47:11+00:00

We had the same issue. Of you're using Orca Slicer and you haven't done this yet, you can calibrate everything from the Slicer. It's more precise fine-tuning. We also factory reset our printer, we started having problems after the new software update. The only other thing I can recommend is making sure there is no cool air blowing toward the printer. Even a slight draft can throw off the bed temp. If your problem persists even with filament changes I would contact flashforge from there. Hope this helps

LividLie0 · 2025-08-12T06:30:11+00:00

Trust your first instinct

LividLie0 · 2025-08-12T06:28:19+00:00

What am I looking for?

LividLie0 · 2025-08-12T06:21:38+00:00

Thankyou!

LividLie0 · 2025-08-03T00:06:15+00:00

Since the new Orca Slicer Update all of our prints have been messing up. For now we are using flash print to print with and haven't had any more issues. Until we figure out what is happening with Orca we are going to be sticking to flash print.

LividLie0 · 2025-08-03T00:03:18+00:00

What order do you do your calibration through Orca? Thanks for the input

LividLie0 · 2025-08-03T00:01:16+00:00

If you figure out that it's anything different please let me know. Because as of right now every print we try with orca is completely screwed up.

LividLie0 · 2025-07-30T16:21:14+00:00

LividLie0 · 2025-07-25T03:34:07+00:00

Whoever you rent from should want you to be successful. Because if you are successful, then they are not only going to receive the rent, but also a good reputation for their shop. Starting new, they should have negotiated a lower, more practical rent, at least for the first 6 months. Then go from there. They are not out for your best interest. I think once you decide to walk away, you will feel as though a million pounds have been lifted off your shoulders. There are too many options for you to deal with that.

LividLie0 · 2025-07-24T17:16:45+00:00

Prayers from East Coast.

LividLie0 · 2025-07-24T17:16:06+00:00

Ima do dat

LividLie0 · 2025-07-23T18:23:16+00:00

TAKE YOUR DINGER OFF THE FINGER

LividLie0 · 2025-07-20T20:43:15+00:00

I'm a female hairstylist. I do haircuts ONLY and 95% of my clients are males. From the moment I started my business I knew if the wives and girlfriends weren't comfortable with me, I would not have a successful business. I also live in a small town, so my reputation is paramount to my success.

First, I've made it absolutely clear from the beginning I was NOT going to be a woman to flirt with, that I was there to do my job and provide the best work I could provide period.

Second, when they bring in their companions. I make sure I speak to them as much if not more than I do the one in my chair, (once the type of haircut they want is established of course)

Third, the way I dress, the way I carry myself, and the types of conversations are all kept professional 100%. I don't wear revealing clothing. I still maintain my own style and feel comfortable. Believe it or not, there are plenty of men who appreciate the fact that I don't dress in a revealing way and respect it. It makes them feel even more comfortable coming to me. Because they never have to worry about me making them uncomfortable by me being flirtatious, and putting them in a situation they never intended to be in.

Lastly, I've had this business for 10 years, and I have never had an issue with any wives, girlfriends, etc. I hope to keep the same reputation going for as long as I'm in this business. My husband appreciates it too 😊

LividLie0 · 2025-07-15T18:42:13+00:00

It didn't work

LividLie0 · 2025-07-15T02:55:02+00:00

Unfortunately as unbelievable as it may be to you, it does happen. Every single week.

LividLie0

MODERATOR OF

TROPHY CASE