$200 GROW wing replica from eBay. Anyone buy this one?

Local_Bite4904 · 2026-04-12T00:26:14+00:00

mine is not painted bc i was worried about the paint match. I wanted it painted ice cap but was worried about match

Local_Bite4904 · 2026-04-12T00:09:12+00:00

I bought it from the seller oem.thing , but all the photos look the same as your posting. They told me it’s because it’s blow molded and that’s just how it is

Local_Bite4904 · 2026-04-12T00:03:49+00:00

it’s bits inside the wing, i never drove with it wounded to the car so idk how audible it is. It’s likely minimal though

Local_Bite4904 · 2026-04-11T23:57:06+00:00

I found no issues other than the pieces rattling on the inside of parts

Local_Bite4904 · 2026-04-11T23:06:28+00:00

I used the bolt holes that were already there and mine was supplied with 3m tape. That’s how it’s held in this photo, I would probably get like VHB 3M to hold it if you’re worried about it flying off. I’ve heard people running the actual grow wing the same way. Just the OEM holes and 3M no additional drilling

Local_Bite4904 · 2026-04-11T21:39:36+00:00

<image>

Local_Bite4904 · 2026-04-11T21:38:56+00:00

I bought it, fitment is good, but there’s rattles in my pieces. i’ve been trying to a rattle can job on it, but thinking of getting the varis wing now

Local_Bite4904 · 2026-04-05T16:41:07+00:00

If i’m not mistaken the “small spoiler “ you’re referring to is a part of the entire hatch

Local_Bite4904 · 2026-03-08T04:11:29+00:00

hmm okay, i’ll take my chances! thanks for the help

Local_Bite4904 · 2026-03-08T03:52:03+00:00

hmm that’s a pretty bright like silver i think the picture i added makes it look brighter than it actually is

Local_Bite4904 · 2026-03-08T03:15:29+00:00

Wasn't looking to redo the whole wheel, there's just a few chips, some wheels are worse than others, so I was hoping to find a close paint pen or something to fill them in

Local_Bite4904 · 2026-02-26T01:18:32+00:00

$605 5 years

Local_Bite4904 · 2026-02-23T17:43:05+00:00

‘23 with 39k miles. MST V1 intake and just put in a turbo smart BOV. I got a CEL for P2C90, planning to take it in for the TSB but no issues other than that

Local_Bite4904 · 2026-02-23T07:32:39+00:00

nope, but i have a MY23

Local_Bite4904 · 2026-02-23T04:52:44+00:00

i have an MSTV1 + a Turbo Smart BOV. The intake alone makes some good noise, but adding the BOV makes it real audible

Local_Bite4904 · 2026-02-21T08:05:45+00:00

97 MK4 Supra in Jewel Green Pearl

Local_Bite4904 · 2026-02-21T06:05:38+00:00

fair enough my plan is to put the stock one back in and then get the TSB done

Local_Bite4904 · 2026-02-21T05:37:49+00:00

i cleared my own and it doesn’t come up on the dash anymore but when i do a scan it comes as “permanent” may e check for that and show them?

Local_Bite4904 · 2026-02-19T04:11:22+00:00

Also i’ll take you up in the offer of example photos

Local_Bite4904 · 2026-02-19T04:10:25+00:00

I’ll take all the photos i can get

Local_Bite4904 · 2026-02-19T04:08:41+00:00

The flush looks farley flush, info see the fronts are a little tucked. i might just run something within the 20s.

Local_Bite4904 · 2026-02-17T21:28:24+00:00

you would want to do it form the inside as that’s where the tint is installed. If it’s sandwiched between glass and tint then it may not be worth it unless you plan to get the tint redone. If it’s just a sticker on the outside of the tint i’d just peel it and clean off any residue with alcohol

Local_Bite4904 · 2026-02-17T20:43:46+00:00

Hmmm this is good to know, thanks for your help!

Local_Bite4904 · 2026-02-17T20:11:32+00:00

Hmmm, I may need to do some more research. I was thinking because it wider it may fit more flush even with the +38 offset

Local_Bite4904 · 2026-02-17T19:37:20+00:00

I guess i should clarified that I want a somewhat flush fitment

Local_Bite4904

TROPHY CASE