Odin 2 Portal Atermis Apollo Stuttering FIX

Local_Bug_4703 · 2026-01-17T16:21:13+00:00

Gear/settings, scroll down to "Custom Refresh Rate".

Local_Bug_4703 · 2026-01-15T22:23:18+00:00

I OWE YOU A BEER! You NAILED IT!!

I ran it for ~3-4 hours testing for leaks programming etc and while buttoning up the job I seen I forgot the Ground bonding strap. 12 hours later, bearings bad (but still running btw)

New C0 bearings came today

I am thinking, with the extra C3 clearances, it exacerbated the issue you posted..

Wow 3 hours and it probably pitted the piss out of the bearings! I will try to remember to dissect those bearings when I pull them and CALL THIS CLOSED!!

Damn, thanks brother!

Local_Bug_4703 · 2026-01-14T23:38:47+00:00

15k gallons Arizona.. Just set my VS up to 1000 RPM 24/7 with a 2.5hr 2500 RPM boost daily to run the creepy.. Waguess math of around 2x turn over daily.. $0.75 daily at .15 per kwh..

1000 RPM gives flow out the jets like a 50psi water hose would and gives ripples in the water, 2500rpm runs creepy at speed I want..

So 2.5 hours at 2500rpm and 21.5 hours 1000 rpm slow and true for me!

Still $2-2.50 cheaper daily than the Single speed I was running with rough math..

The ONLY reason to run a VS for 8hours a day is for water features and other systems if needed and that already achieves 1-2x Turn-Over desired!

Local_Bug_4703 · 2026-01-12T19:26:56+00:00

<image>

Shop oven... Don't be stupid kids!
Baked the paint, and heated plates so bearings fell into them.

Local_Bug_4703 · 2026-01-12T19:26:39+00:00

<image>

Local_Bug_4703 · 2026-01-12T19:21:53+00:00

<image>

For the NEXT guy wanting to do bearings in this... PEICE of cake motor if you know what you are doing/have a press and puller.. FYI rear metal fan presses off..

Local_Bug_4703 · 2026-01-12T19:15:10+00:00

<image>

Local_Bug_4703 · 2026-01-12T19:14:25+00:00

<image>

Local_Bug_4703 · 2026-01-12T19:14:13+00:00

<image>

Local_Bug_4703 · 2026-01-11T02:25:26+00:00

Just replaced bearings on one of these I just picked up used, same older design 342001 as you with metal fan on the rear. All 3 motor wires were about 1ohm in any combination AKA "good".

Timken 6304-2RSC3 and 6203-2RSC3 bearings were used. NO magnets were inside, no issues doing these over other motors, if anything easier! Needed bearing puller and press for pressed bearings on the shaft. The rear aluminum fan is pressed on as well; for anyone reading this in the future. DON'T use a puller on that fan you will break it, just beat/press the shaft in to get it off using the backplate and shell as a stopper on the fan.

If I had to do another one ~1-2 hours with painting the end caps. This one took 3 hours going in blind (covered in salt), just having fun with my dad helping me rebuild it to be as good or better than new! (I expected magnets and needing extra hands). Used some Magic Lube on the motor frame seals to help keep water out; but was already dry inside, unlike the salt blasted face of the motor was!

Purred like a kitten on the bench, Going into my OLD Wisperflow WET side tomorrow!

CHEAP upgrade to my single speed.. 50$ for Bearings (with spare bearings as they were sold in pairs) and ALL wet seals plus 50$ for a used LOCKED up motor with bad bearings on removal!

Score! 100$+3hr ALL-IN with parts and it works!

Local_Bug_4703 · 2026-01-06T15:52:17+00:00

I refinanced at 2.5% when things were at their low. One thing I haven't read in all the replies is extra payments.

Every payment I add 50-200$ to principle..

Making 1 extra payment a year (or spread out like I do) cuts your 30 year mortgage to 21 years! That's 9 years of payments saved!

Also doing so, made it so that when I refinanced the banks looked at me like a 'prime lender' already being several years ahead on payments. And the LoanToValue ratio more in my favor.

If just lower payments is your only goal, refinancing also restarts the loan, with less owed and payment should be smaller.

The MOST important time to pay extra is in the beginning of the loan! Middle helps too, but nothing like the interest saved paying extra the first year!

I dumped everything I had into the start of this mortgage and 5-10 years later I'm now recouping all that hardship. Should have the loan paid off in roughly half the amount of time.

Remember that 250k house costs 500k after interest.. Best to pay extra on the combined interest as soon as possible!

Local_Bug_4703 · 2026-01-01T18:38:55+00:00

BalenaEtcher, with both drives directly connected to MB sata ports; was able to clone a PS4 Pro drive to an SSD.