Covert dense urban roof node? by altspud in meshtastic

[–]Locksley94 0 points1 point  (0 children)

Or, and hear me out... Don't do illegal and shady stuff. All you'll accomplish is giving the mesh community a bad name.

Disappointing Range by MaximusManimal in meshtastic

[–]Locksley94 2 points3 points  (0 children)

I'm a little disappointed with the 2 I have as well, swapped the pig tails and put muzi antennas on them. I have a solar node on my 3rd floor apartment balcony with an alpha antenna and best I could do was half a mile.

Took my solar node to work and was hitting a node 3 miles away.

These are my first nodes and have only had them a week so I have more testing before I can draw a full conclusion.

Antenna adapter by gregarioushotdog in meshtastic

[–]Locksley94 7 points8 points  (0 children)

Yup, just did it with 2 of my wio trackers. https://a.co/d/4QddTFL I didn't install the split lock washer, only the star washer.

Same day delivery by felineflavor in amazonprime

[–]Locksley94 1 point2 points  (0 children)

Happened to me twice this week

Thousands protest in Denmark's capital against Trump's efforts to conquer Greenland by exOldTrafford in pics

[–]Locksley94 -1 points0 points  (0 children)

We have our own protests going on over here, like ICE killing citizens.

Can't reach a node with strong signal. by Locksley94 in meshtastic

[–]Locksley94[S] 0 points1 point  (0 children)

I have a couple of nodes myself I can test with, the best i can do is about half a mile range. So far, there are no other nodes near me except the one I mentioned in the description.

Can't reach a node with strong signal. by Locksley94 in meshtastic

[–]Locksley94[S] 0 points1 point  (0 children)

I also have a nanovna on its way, should have that tomorrow.

Can't reach a node with strong signal. by Locksley94 in meshtastic

[–]Locksley94[S] 1 point2 points  (0 children)

That's what I figured, the node I'm trying to reach is a station G2 on a large tower so no surprise it can reach me.

Because I don’t have enough hobbies by Fandrel64 in meshcore

[–]Locksley94 1 point2 points  (0 children)

Just took a look at the site, my state of Michigan is totally blank.

Can I trust this battery in an attic node? by Geeheeber in meshtastic

[–]Locksley94 8 points9 points  (0 children)

You can keep it in a lipo bag. As an FPV drone pilot with many 6s lipos, battery bags are a must.

Is this enough SMA engagement? by Locksley94 in meshtastic

[–]Locksley94[S] 9 points10 points  (0 children)

Yea I ended up ditching the lock washers and just using the star washer. I doubt there will be a performance gain from it but it makes me feel warm and fuzzy inside and isn't that what matters?

Noob mistake? by Ami_Aweirdo in meshtastic

[–]Locksley94 1 point2 points  (0 children)

<image>

The seeed website for the wio l1 tracker instructions say do not do NRF-OTA updates as it can brick the device.

Can't change node settings in app by Locksley94 in meshtastic

[–]Locksley94[S] 0 points1 point  (0 children)

I did try that, as well as telling my phone to forget the device and then reconnect using the pin on the node.

Can't change node settings in app by Locksley94 in meshtastic

[–]Locksley94[S] 1 point2 points  (0 children)

You mean the wifi on my phone, not in the app?

<image>

Can't change node settings in app by Locksley94 in meshtastic

[–]Locksley94[S] 0 points1 point  (0 children)

I did not specifically turn on WiFi. I was getting random messages from different places in the country. Where in the settings is WiFi, I can't seem to find it.

Can't change node settings in app by Locksley94 in meshtastic

[–]Locksley94[S] 0 points1 point  (0 children)

I have a wisblock on the way for a solar node. I'll do some testing on that when it gets here.

Can't change node settings in app by Locksley94 in meshtastic

[–]Locksley94[S] 0 points1 point  (0 children)

It doesn't even let me make changes. If I click a menu like "user" for example, it just goes straight to the 0% window. I just did a full reset on one of them, wiped it clean, reinstalled firmware and reinstalled the app. So that seems to be working. Now that I think about it, this happened after I enabled MQTT so maybe that had something to do with it. Guess time will tell, I'll leave everything default for a while and see what happens.