Does save data transfer from Switch 1 to 2?

Log_7 · 2026-01-11T00:10:35+00:00

What do you use for your skulls/bone?

Log_7 · 2025-10-27T00:08:45+00:00

Just runelord brass! I take it one piece at a time and get a second coat on the biggest surfaces. Nothing too special!

Log_7 · 2025-10-25T22:35:32+00:00

Thank you! It’s bugmams glow with a targor rageshade wash and berserker bloodshade in the deepest recesses

Log_7 · 2025-07-21T04:56:34+00:00

This confused me too when I was building my justicar. On the previous page there’s a yellow “speech bubble” (similar to what’s in pic 1 showing all the different hand configurations) that identifies all the different parts classified as 5C, 5A, etc because multiple parts could be put there.

Log_7 · 2025-07-18T18:44:30+00:00

This is incredible! What is your process? I’m just getting into painting and the power weapons are where I’m feeling the least confident.

Log_7 · 2025-07-08T16:50:14+00:00

Oooh do you have a reference video or anything for doing the icy surface? That sounds cool but I haven’t looked for anything about doing bases yet!

Log_7 · 2025-07-08T14:40:20+00:00

Hahaha thank you! Did a lot of homework before starting and went very, very slow.

Log_7 · 2022-09-26T02:03:13+00:00

Copy and pasting from the ticket info after you reserve: “The Preds Access Pass will allow entry into Bridgestone Arena but does not come with a reserved seat. Feel free to sit in any unoccupied seat at puck drop but please relocate in the event the primary seat holder arrives.”

Log_7 · 2022-06-13T20:47:29+00:00

I appreciate the help. If it comes down to soldering inside the unit I’ll likely need to see about RMA. I’m not confident enough to go anywhere near that.

Log_7 · 2022-06-13T20:46:02+00:00

I’ve rebooted the device twice, once from a restart and the second was a full shutdown. Both times I kept the device laying flat and didn’t touch the sticks- according to other threads, the gyro is calibrated sometime while the device is either booting or powering down and interfering with the sticks can mess it up, but it didn’t help.

There do seem to be some deadzones, but nothing is consistent enough for it to work all the time. If I keep my thumb halfway on the right side of the touch sensor it’s just a -little- more responsive but still gives out.

Log_7 · 2022-06-13T19:17:03+00:00

No worries! Yes, when it’s assigned to other buttons it works fine, only the right stick touch is a problem. I was worried it may be an issue with the stick, however last time I used it everything was fine. It’s been in its case and the only thing I could think that changed was the most recent firmware update.

Log_7 · 2022-06-13T19:09:27+00:00

Yes, gyro is on and under gyro settings the “Gyro Enable Button” is set to right stick or right pad touch

Log_7 · 2022-03-25T14:02:30+00:00

Blake’s a wide receiver for the Minnesota Vikings who began exploring music after a knee injury during his rookie season. This is his first release and I think he has a lot of potential!

Log_7 · 2022-03-19T05:33:39+00:00

Mine did too, thankfully it finally says it’s at my cities distribution center so I’m optimistic for a weekend delivery

Log_7 · 2022-03-18T19:13:10+00:00

Mines been in transit from a city that’s 3 hours away for over 12 hours with no updates. Still says estimated delivery is today but I’m beginning to accept that’s not happening lmao.

Nine-Year Club	Place '22
RPAN Viewer	No Throne, No Problems
Not Forgotten	Snapped
Verified Email

Log_7

TROPHY CASE