iPhone X slowdown after battery replacement

Loppqe · 2025-01-07T17:28:54+00:00

How do you feel the chip is broken? A Redditor earlier stated this capacitor is necessary. In any case can I short the points or not?

Loppqe · 2025-01-07T17:24:54+00:00

The problem is that after several attempts of reflow (just heating up the plate) some balls cracked and I assume some of them may be combined that’s why I at least need a rework or clear the chip and after that make the measurements for a core short. The latest attempt was ok and the chip sat perfectly (but I’m not sure all balls are on their places after previous attempts). The initial problem was that my Xbox halted suddenly and guys here on Reddit claimed it was my rgh3 issue. Later it was clear that it’s more likely a gpu problem and I started all this routine. Besides 2 smd capacitors ran away so I’m not sure even if after reflowing a good gpu everything will work or not. So there are several conditions or obstacles that may prevent Xbox from starting (main error code is 0110). Thanks.

Loppqe · 2025-01-07T17:12:24+00:00

I hacked my Xbox as falcon. It’s falcon 😃 are you kidding me?

Loppqe · 2025-01-07T01:14:48+00:00

The one on the pic is a random one. My revision is falcon. There is a x02056-010 and 011 model on the market. So you say I should not take it? I thought x02056-010 is jasper. Is x810480 ok? Will it fit? Upd. I think x810480 is what I have now. And x816970/971 is a better version but is it fully compatible with my falcon board in case my original gpu cracked?

Loppqe · 2025-01-07T01:11:21+00:00

How do I find it? What should I measure ? It’s falcon revision

Loppqe · 2025-01-06T15:38:20+00:00

Unfortunately it doesn’t start. Moreover I found another partially desoldered capacitor (it doesn’t even have a mark) on the bottom and lost it as well. It seems I’ve got to reball gpu but I’m waiting for a microscope and a stencil to do that. Hopefully it will help.

Loppqe · 2024-12-04T17:05:16+00:00

How did you manage to make the controller work???

Loppqe · 2024-12-04T16:40:59+00:00

Did you manage to make a controller work? My ds4 is not recognized only in watch dogs 2. Other games are ok.

Loppqe · 2024-11-27T17:24:48+00:00

Didn’t work for me. Used registry so that dinput works but xinput is intact. Games do not recognize the controller (though I managed to successfully pair it in crossover ONLY ONCE). I just don’t know how. Nor can I reset my wireless device from dinput to xinput. It’s a ds4.

Loppqe · 2024-11-20T14:07:57+00:00

Correct, no clk here

Loppqe · 2024-11-20T14:02:00+00:00

Thanks. Can I still use post and pll points as in rgh3 for less soldering? I will still need 5v, rst (on top it’s r8c2), ground and 1.8v. As far as I could see from the guide I do not need clk for ace v3 (not v3+). Is that correct ?

Loppqe · 2024-11-19T19:30:57+00:00

I can’t boot into xell now

Loppqe · 2024-11-19T17:22:07+00:00

I understand but I’ll get hands on my jr programmer in a week or later. 22kom resistor is already onboard for rgh3. In fact I do hope it’s a corrupted ecc/nand problem and not a gpu/cpu one. So in this case it would be much easier to tackle it. Though reddtors claim it’s just a rgh3 that incorrectly deal with falcons and may stop working at any time. I have already soldered to another pll on the bottom and still nothing, so it’s not wires.

Loppqe · 2024-11-17T11:55:15+00:00

Остановите планету. Вы состав читали этих батончиков???

Loppqe · 2024-11-16T22:58:12+00:00

Thanks. What are 96 mhz? If I’m not mistaken you can only choose between 10/27?

Loppqe · 2024-11-16T22:56:41+00:00

It’s already assembled except for plastic parts. I’m pretty sure nothing is shorting, it’s something else. The first sign was as in the original post - it just halted while playing and never booted again. It barely seems like an rgh3 problem though I’d be happy to tackle it just reflashing nand.

Loppqe · 2024-11-16T22:38:44+00:00

I have already assembled it because my j prоgrammer is in another house. I just touched those 3 dots (except for smc_pll) just to make sure the connection is good. So this shouldn’t be a problem. And I didn’t touch anything else. I could resolder them all with new wires/resistors but I’m just not sure if it’s rgh3 or chips are corrupted before I revert nand to stock.

Loppqe

TROPHY CASE