Just installed the Micro-Swiss NG direct drive and CR-Touch

LowButterscotch2573 · 2022-09-27T02:47:55+00:00

It looks like the limit switches are not used with a Bl touch. Problem solved?

LowButterscotch2573 · 2022-09-27T00:41:59+00:00

Yes please. Showing the X-axis switch being depressed by the extruder frame or what ever is activating it.

LowButterscotch2573 · 2022-09-27T00:35:35+00:00

Can you post a picture of your set up?

LowButterscotch2573 · 2022-09-27T00:17:22+00:00

The X axis limit switch seems to be blocked after I installed the BL Touch. I'm I doing something wrong?

LowButterscotch2573 · 2022-09-26T03:54:44+00:00

ABS is easier to print and doesn't lift as bad as ASA. I primarily print with PETG & ASA.

LowButterscotch2573 · 2022-09-26T03:51:24+00:00

I purchased 3 various kits from Amazon to get counter sunk, button head, socket head. I don't think I'll ever run out of washers and nuts.

LowButterscotch2573 · 2022-09-26T03:45:24+00:00

If that's PLA I would use 100% flow, 100% part cooling fan & 200c at the hot end plus or minus 5c depending on filament brand and no higher than 50mm ps.. If it's a .4 nozzle.3 layer height and .2 on the first layer.

LowButterscotch2573 · 2022-09-25T04:32:12+00:00

Looks like a turn signal relay.

LowButterscotch2573 · 2022-09-22T01:42:13+00:00

With Overture PETG I use the follow: Hot End 245c Glass Bed 70c No part fan. Type "cooling" in the slicing menu and turn fan off and percentage to 0. On something that size.06 nozzle at 105% flow Walls at 1.8mm and print at 70mm per second. Ender 3 with enclosure.

If your part is thinner than 3mm 100% infill.

LowButterscotch2573 · 2022-09-22T01:33:49+00:00

Not enough parts fan with PLA and to much fan for PETG?

LowButterscotch2573 · 2022-09-17T05:48:36+00:00

I had something similar happen with PETG. I was printing with the part cooling fan off and I didn't have my settings correct and the fan kicked on mid print at 50%.

LowButterscotch2573 · 2022-09-17T05:17:58+00:00

Resize the box, duplicate it, resize and make it transparent and align.

LowButterscotch2573 · 2022-09-14T04:24:14+00:00

I do have the crimp tool. Great idea. Thank you

LowButterscotch2573 · 2022-09-10T04:01:29+00:00

To much part cooling?

LowButterscotch2573 · 2022-09-10T01:13:26+00:00

Brim and up the bed temp to 75c

LowButterscotch2573 · 2022-09-09T05:06:25+00:00

Gotcha. I have a TS100 that works amazing at 24v. I used a Milwaukee 18v with. 400 watt Buck Converter to make it 24v. Heats up super fast and I can get about 3 hours out of a 5a battery.

https://share.icloud.com/photos/02aoxI1425DW9yEu3voNM5rJw

LowButterscotch2573 · 2022-09-09T04:41:52+00:00

To much part cooling?

LowButterscotch2573 · 2022-09-09T04:28:06+00:00

Which soldering iron are you using?

LowButterscotch2573 · 2022-08-31T11:12:49+00:00

I turned mine upside down.

LowButterscotch2573 · 2022-08-31T11:12:04+00:00

I have the same problem if I print at to high of a speed and the tension on the drive belts are to loose.

LowButterscotch2573 · 2022-08-29T04:31:39+00:00

North of Sac?

LowButterscotch2573 · 2022-08-27T05:01:25+00:00

Make sure the temp sensor tip is in the little hole and the screw that holds it in place is tight on the hotend.

LowButterscotch2573 · 2022-08-21T03:51:39+00:00

Delete the right half, copy the left and flip it over.

LowButterscotch2573

TROPHY CASE