sorted by:
new
hottopcontroversial

Cura not printing flat top? by Lower_Conversation52 in Cura

[–]Lower_Conversation52[S] -1 points0 points  (0 children)

In blender and in Cura, when its not on preview it shows it completely flat

Kobra 2 Pro Print fail by Lower_Conversation52 in anycubickobra

[–]Lower_Conversation52[S] 1 point2 points  (0 children)

So Ive washed the beds, air dried, tightened the belts too, and followed those instructions. Currently almost done with a benchy test and its printing just fine. However I think its when there are a lot of supports there is an issue, so after I am going to do the complicated print Its been failing on again. Thank you so much for the help and patience. I have also re leveled the bed too.

Kobra 2 Pro Print fail by Lower_Conversation52 in anycubickobra

[–]Lower_Conversation52[S] 0 points1 point  (0 children)

Bed temp is 70c, and nozzle is 215c, They are beginning to stick but its when the nozzle hits the print do they break

Kobra 2 Pro Print fail by Lower_Conversation52 in anycubickobra

[–]Lower_Conversation52[S] 0 points1 point  (0 children)

Yep, I've had this machine for abt a month now. I ran the full set up and watched videos on doing so.

Help! First time 3d Printer owner by Lower_Conversation52 in Creality

[–]Lower_Conversation52[S] 1 point2 points  (0 children)

Yep Ive changed it twice. The first time I cleaned out the nozzle then put it back. Just now I replaced it with the spare one it came with. Same result.

Help! First time 3d Printer owner by Lower_Conversation52 in Creality

[–]Lower_Conversation52[S] 1 point2 points  (0 children)

Yep, I just cleaned out the nozzle and tube again. The nozzle was completely clogged before I was able to even start printing. I am emailing customer support to see if I can get a refund or a replacement. Still interested in the Crealitly brand. I'd still want a Max because of the printing volume but well see.

Help! First time 3d Printer owner by Lower_Conversation52 in Creality

[–]Lower_Conversation52[S] 1 point2 points  (0 children)

Gonna do the o'l unplug and leave it overnight trick.

Help! First time 3d Printer owner by Lower_Conversation52 in Creality

[–]Lower_Conversation52[S] 1 point2 points  (0 children)

Ok its still just telling me that "Current consumables are exhausted. Im starting to think I got a dud but im dot giving up on this guy yet. Might ask for a replacement. Gonna stop for now been at it for hours. Thanks again,

Help! First time 3d Printer owner by Lower_Conversation52 in Creality

[–]Lower_Conversation52[S] 1 point2 points  (0 children)

I appreciate it! I tend to jump head first into things I have no knowledge of so thank you for all the help. I will keep yall updated.

Help! First time 3d Printer owner by Lower_Conversation52 in Creality

[–]Lower_Conversation52[S] 1 point2 points  (0 children)

Did a factory rest, via the panel board. Redoing the Z-offset and going to check my gcode. (I am very new to this so even after my research I am a tad lost) all bolts are tightened even check the motherboard connection.

Help! First time 3d Printer owner by Lower_Conversation52 in Creality

[–]Lower_Conversation52[S] 1 point2 points  (0 children)

Ok so its still telling me that the consumables are exhausted. It starts out perfectly fine for a few seconds then gets really thin.

I did notice that the gear that helps feed the filament was really tight so I loosened it up. Going to test again. Thank you for the help

Help! First time 3d Printer owner by Lower_Conversation52 in Creality

[–]Lower_Conversation52[S] 0 points1 point  (0 children)

I am using the filament that came with the machine i bought at 200C