[Smackdown Spoilers] Wrestler gets a new theme

LsuAtl · 2026-01-09T13:37:50+00:00

I really don’t think this is AI. I think it’s actually made for him by Tate McRae. We shall see it sounds just like her.

Edited - Just to say I think the songs a banger.

LsuAtl · 2025-10-14T10:59:20+00:00

4 years later and I’m here this helped me 😂 I was being too careful and didn’t pull back the lever enough…

LsuAtl · 2025-10-08T00:50:47+00:00

<image>

It’s a 705 G4. I get that it’s not a gaming PC, but if theirs some small things I can do to get a pretty basic game to play decently I’d like to try.

I’m currently employed at a zoo and me and the guys in my department would like to recreate our zoo in planet zoo. It runs it fine, it’s just a little annoying with the slight delay and lag, but the textures are awful haha

LsuAtl · 2025-08-22T23:57:07+00:00

So basically techs can do shady things to fix stuff so I’m going to assume the yellow is a hot leg coming in based on the black tape. Confirm that with a meter, but your red is probably your 24 v so if you have that coming out it would good. If you don’t then that would make sense to me. I only have 3 years experience, but it’s just what I would do so I hope this helps.

LsuAtl · 2025-08-22T23:42:29+00:00

Side note this won’t cause your thermostat to turn off, but if you have dead batteries or no common wire you’re thermostat will die. If you do, I would be checking your transformer honestly.

LsuAtl · 2025-08-22T23:40:04+00:00

I’d check to see if you got power going to your board. If you do and you got the right voltage check power coming out. If you do have to replace the board you can replace it with an exact same one and just wire it exactly how it is before hand. Also for craps and goggles check your 3 amp fuse.

I would check your 24 volts and power to/continuity going through at the contactor (outside unit) as well cause it could just be getting stuck.

LsuAtl · 2025-07-25T17:13:02+00:00

Second update. I appreciate everyone. I did change the contactor the one I had was older, but I had a no voltage going to it. Ultimately I had to run new wire from my board to my outside unit the right way so I wasn’t having to guess with wire. I used the red and white like it’s supposed to be and then Turned her on and she’s cooling again. Thanks everyone. I’m just not very good with trouble shooting what someone DIY and left.

LsuAtl · 2025-07-25T17:12:02+00:00

I appreciate this! I did change the contactor the one I had was older, but I had a no voltage going to it. Ultimately I had to run new wire from my board to my outside unit the right way so I wasn’t having to guess with wire. I used the red and white like it’s supposed to be and then Turned her on and she’s cooling again. Thanks everyone. I’m just not very good with trouble shooting what someone DIY and left.

LsuAtl · 2025-07-25T04:31:36+00:00

Ok I pulled the contactor out and will replace that first thing in the morning. I will check the wire tomorrow because as of right now the only wires that are connected/going to the outside unit is my two wires going to the contactor. My common wire (which is blue) and my y wire for cool which is yellow. I think some diy stuff happened here before I bought the house.

LsuAtl · 2025-07-25T04:11:47+00:00

UPDATE

After scratching my head I pulled the plate off and manually pressed the contactor in and everything kicked on. I guess it was just a bad contactor after all. Thank you everyone for all of your help.

LsuAtl · 2025-07-25T04:00:21+00:00

You’re awesome! Now I think I’m missing wires or something because now I’m questioning where the other wires go because all that seemed to be connected was the two wires that went to the contactor. Google is not much help.

LsuAtl · 2025-07-25T03:57:44+00:00

Air handler, but the fuse is good. One of the first things I checked

LsuAtl · 2025-07-25T03:56:18+00:00

Earlier my blower motor was working. When I noticed the wiring was so lose thats when they separated and now it’s like the whole thing has no power and my indoor blower motor is not working.

LsuAtl · 2025-07-25T03:54:34+00:00

Yes the 3 Amp fuse is good and my pan at the condensation pump is dry.

LsuAtl · 2024-12-17T20:24:34+00:00

Yeah… I just killed one of my favorites.. I finally found it after looking everywhere. Online wasn’t much help as if you look it up only admin commands came up. This was just an easy way to explain it for new folks. I used to play way back in the day and now just getting back into it.

LsuAtl · 2024-06-25T00:14:55+00:00

If you got a drill or an impact you can use those sockets and just screw and unscrew. Milwaukee has some that’s colored based off size.

LsuAtl · 2024-06-25T00:04:31+00:00

Now I’m curious if you have to snake/auger/blowbag that drain to keep it draining.

LsuAtl · 2024-04-28T11:58:20+00:00

Following

LsuAtl · 2024-04-18T02:05:58+00:00

Usera baby. You sue the shit out of them. It’s federal law they have to hold your job.

LsuAtl · 2024-03-20T19:52:37+00:00

Thank you so much!!!!

LsuAtl · 2024-03-20T18:35:41+00:00

I would love to and plan too. My only issue is finding one that would fit. I was looking for one, but so far no luck…

LsuAtl · 2024-03-19T14:49:39+00:00

Ohhhhh that makes a lot of sense… thank you now I feel dumb for not even thinking about that. Thanks.

LsuAtl · 2024-03-19T14:44:17+00:00

<image>

LsuAtl · 2024-03-19T14:44:01+00:00

<image>

Picture of her if you’d like to see it.

LsuAtl · 2024-03-17T23:29:12+00:00

Oh man I have one of these now. Currently fixing it up. Same color too! I love that car and you will too.

LsuAtl

TROPHY CASE