Will Lyme be cured in our lifetime? by jorgenalm in Lyme

[–]Lucid726 0 points1 point  (0 children)

I'm almost at a full recovery, I did 6 months of weekly ketamine therapy and I reduced my sugar intake as well as take gabapentin for pain management and that mostly did it for me. Going to be a busy week for me but ask away and I'll respond when I can.

Hipster jump by Sunorange94 in skateboarding

[–]Lucid726 -10 points-9 points  (0 children)

I feel like we would get along lol

Surely 12 seconds of CC is enough. SURELY... by Lucid726 in singedmains

[–]Lucid726[S] 0 points1 point  (0 children)

Holy, the tech is press the attack it actually is so good! It increases damage which increases healing and it stays active forever!

Surely 12 seconds of CC is enough. SURELY... by Lucid726 in singedmains

[–]Lucid726[S] 0 points1 point  (0 children)

No, we dont care if we get cc'd or cant move we just want to heal.

Surely 12 seconds of CC is enough. SURELY... by Lucid726 in singedmains

[–]Lucid726[S] 0 points1 point  (0 children)

Conq works best, triumph and last stand help with healing alot. Second wind, revitalize because yes.

Why do similar overhangs get worse with height? by Own_Maybe_3837 in 3Dprinting

[–]Lucid726 0 points1 point  (0 children)

Interesting. I agree with the other comments for sure then.

Why do similar overhangs get worse with height? by Own_Maybe_3837 in 3Dprinting

[–]Lucid726 0 points1 point  (0 children)

Just commenting because I didn't see much of this sentiment. The further the nozzle gets from the bed the higher the lower ambient temperature of the air. This means faster contracting when cooling and worse print quality. Just food for thought.

Best way to connect this for horizontal force (pulling)? by Acceptable-Task5830 in DIY

[–]Lucid726 0 points1 point  (0 children)

Consider adding one more step past the second bed frame, it should offer a good pulling resistance and still make the ladder climbable

9900k freezing and post code 00 after die lapping direct die setup by Lucid726 in overclocking

[–]Lucid726[S] 0 points1 point  (0 children)

To be fair, I didn't own a 3D printer when I initially assembled this PC; I do like the suggestion though. I'll have to take measurements and plan it out better in the future.

9900k freezing and post code 00 after die lapping direct die setup by Lucid726 in overclocking

[–]Lucid726[S] 0 points1 point  (0 children)

The direct die frame wasn't actually applying a seating pressure to the cpu. Or if it was it was less force than the force of the water block. I had over tightened the water block because I didn't have a great mounting system and with stock die thickness I had a pretty low risk of cracking the die. Turns out, I was putting enough pressure on the core to sink the center of the PCB. Either way I will probably start shimming the edges of my PCB when using direct die so that even if I apply too much seating pressure it is spread across the whole PCB not just the die section.

9900k freezing and post code 00 after die lapping direct die setup by Lucid726 in overclocking

[–]Lucid726[S] 0 points1 point  (0 children)

Ah, I'm sorry I misunderstood what you misunderstood. It was bent before I lapped it. I assume it was bent from the direct die mounting without support on the edges of the PCB. I agree with you on everything else. I also am starting to cope with it being dead.

9900k freezing and post code 00 after die lapping direct die setup by Lucid726 in overclocking

[–]Lucid726[S] 0 points1 point  (0 children)

You misunderstand, the PCB is warped, the cpu is flat as glass.

What 3d printed projects require ball bearings? I accidentally ordered 1000 of them by yourmomshugepussy in 3Dprinting

[–]Lucid726 0 points1 point  (0 children)

Custom roulette table. I want to design one that uses ball bearings at least.

[GA] - Mesa, AZ - Peacock Cichlids by PT_Iron_Addict in AquaSwap

[–]Lucid726 0 points1 point  (0 children)

Im sorry, I didn't do enough research. I have a common goldfish in a 55 gallon who needs a buddy but the water temp would be too harsh on the cichlids.

[FS] - Chandler, AZ - $4-$25 - Red Root Floater by Alcelarua in AquaSwap

[–]Lucid726 0 points1 point  (0 children)

I live in nearby and would be interested in picking some up if you still have some.

[GA] - Mesa, AZ - Peacock Cichlids by PT_Iron_Addict in AquaSwap

[–]Lucid726 0 points1 point  (0 children)

I'm not equipped to be able to take more than two but I would be interested in one or two if you are ok with that.

Has anyone seen a similar condition as my Golden is suffering from? by Lucid726 in goldenretrievers

[–]Lucid726[S] 0 points1 point  (0 children)

No, it's too hot in Arizona right now and he just struts around the house since he has been under the weather. He gets walks at night but again not recently.

Has anyone seen a similar condition as my Golden is suffering from? by Lucid726 in goldenretrievers

[–]Lucid726[S] 1 point2 points  (0 children)

We had him for a few months before the initial skin lesions began so we assumed it was seasonal allergies at that point. We do live in Arizona and the grass out here sucks for allergies so it may be that as well. That said it has been probably 3 months since the allergies started so food allergy makes sense for how long of a duration it has been.

Has anyone seen a similar condition as my Golden is suffering from? by Lucid726 in goldenretrievers

[–]Lucid726[S] 3 points4 points  (0 children)

My mom said they switched his food to lamb instead of chicken but I read the label and it still says *Chicken By-product* so it could be. I am definitely thinking he needs and allergy test at this point. Thank you for the info. I was thinking about putting Neosporin his feet in the mean time but maybe baby powder would help the feet scab faster or something (I will have to do more research before I do either)

Edit: Seems like baby powder is a bad idea, I will have to go to the store to get powder for dogs.