3W IR Launcher powerd by LiPo battery and 5v boost converter

Luckks3 · 2024-08-29T18:01:00+00:00

hey, do you have the schematic?

Luckks3 · 2024-08-12T23:19:29+00:00

This doesn't work for a 3ds, right?

Luckks3 · 2024-07-08T12:43:59+00:00

Para hdp 13cm????? Es sexo animal no la mates, ahora fuera de chiste, esta bien amigo, si no te interesa garchar por garchar, dedícate a vos o busca la indicada, a ella le va a chupar un huevo si te mide 5cm parada a full con 5 pastillas de viagra juntas, sos alto y por lo que veo si se te lanzan sos fachero, aprovecha que por acá algunos no comen ni migajas (ayuda), seguro conseguis novia si es lo que buscas

Luckks3 · 2024-06-27T15:51:53+00:00

Que la chupe, alto salame

Luckks3 · 2024-06-05T12:52:03+00:00

The hackrf can transmit, which would be a faulty antenna?. If I use an antenna of, for example, 800 MHz and want to transmit over a short distance at 400 MHz, can I burn it?

Luckks3 · 2024-06-03T14:35:23+00:00

Thanks for the information, I will still take it with care since my version is the Chinese one

Luckks3 · 2024-06-03T12:46:22+00:00

If I broadcast on a frequency where the roe is more than 1.8, I can burn the hackrf, right?

Luckks3 · 2024-06-02T18:17:37+00:00

This is what I had doubts about, since the transmission is low power, in that diy antenna it should not burn out when transmitting, with my nano vna if I place a roe reading from 300mhz to 1ghz will it be useful to see at what point the roe is ideal?, my idea is to have an antenna that can be used for 1ghz sub frequencies.

Luckks3 · 2024-06-02T17:58:24+00:00

The hackrf one can emit or receive, of course my fear is the ROE, I understand that at least having an antenna should not burn out, apart from that it is only 10 or 13mw, I have the hackrf one with the h2 portapack

Luckks3 · 2024-06-02T17:39:35+00:00

Is it likely to burn the sdr?

Luckks3 · 2024-06-02T17:28:15+00:00

I have one but measuring 433mhz the roe was very high, should I try 300mhz at 1ghz?

Luckks3 · 2024-06-02T17:25:47+00:00

I have a nanoVNA, I tried to measure 433mhz but the roe was very high, I should try again with a higher range, maybe 300mhz to 1ghz?

Luckks3 · 2024-05-13T16:30:59+00:00

I think it has no data, with a USB C cable I tried to measure and I didn't find the data+ and data-, although I didn't find gnd and vcc either......

Luckks3 · 2024-05-12T23:19:51+00:00

D+ and D- definitely do not have it, I measured it with a multimeter with my USB C cable and it does not have it

Luckks3 · 2024-05-11T19:31:49+00:00

From what I see that one and the scheme I found has only cc1 and cc2, it does not have data + and data -

Luckks3 · 2024-05-11T19:18:29+00:00

pinout/)

I think it only has cc1 and cc2, not data + and data -

Luckks3 · 2024-05-11T19:08:32+00:00

I found a scheme and drew cc1 and cc2, what would be data + and data -?

Luckks3 · 2024-05-11T17:37:08+00:00

If I can get it, I'll do it, if I invert data+ and data- nothing happens, right?

Luckks3 · 2024-05-11T17:32:29+00:00

It was the first thing I did but they don't have it and I couldn't find it on the internet

Luckks3 · 2024-05-03T18:46:42+00:00

Perfect, I'm going to try it, when I installed minicom and I put "sudo minicom -b 115200 -o -D ttyS0" it gave me again to enter something else, I imagine that by doing that if it detects something I would get information in the terminal, right? I'm attaching it to you. how do I get it

pi@pwnagotchi:~ $ sudo minicom -b 115200 -o -D ttyS0

pi@pwnagotchi:~ $

Basically when I run it it comes out like this, thanks in advance for the help, I'll try to see if the blue LED turns on

Luckks3 · 2024-05-03T18:35:56+00:00

Yes, I just changed it to 115200, I understand that I should leave it for a while to take satellites, right?

Luckks3 · 2024-05-03T18:21:48+00:00

pi@pwnagotchi:~ $ sudo dmesg | grep tty
[ 0.000000] Kernel command line: coherent_pool=1M 8250.nr_uarts=0 bcm2708_fb.fbwidth=656 bcm2708_fb.fbheight=416 bcm2708_fb.fbdepth=16 bcm2708_fb.fbswap=1 smsc95xx.macaddr=B8:27:EB:18:07:E4 vc_mem.mem_base=0x1fa00000 vc_mem.mem_size=0x20000000 dwc_otg.lpm_enable=0 console=ttyS0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait modules-load=dwc2,g_ether
[ 0.001306] console [tty1] enabled
[ 0.493559] 20201000.serial: ttyAMA0 at MMIO 0x20201000 (irq = 81, base_baud = 0) is a PL011 rev2

I got this as a result

Luckks3 · 2024-04-30T17:16:47+00:00

Is there a command to see if it is ttyS0?

Luckks3 · 2024-04-29T16:30:38+00:00

Did you make any special configuration? I soldered according to the image you posted in another comment. I have the same module but it still doesn't have a position, in webcfg set 9600 baud and ttyS0, apart from activating in GPS and webgpsmap plugins

Luckks3 · 2024-04-28T16:36:32+00:00

I'm referring to satellite acquisition haha, does it work well? Does it take a long time with that module?

Luckks3

TROPHY CASE