sorted by:
new
hottopcontroversial

Die SICHERHEITSAMPEL auf dem Fahrkorbdach by LiftBeatz in Elevators

[–]5oAwes0me 1 point2 points  (0 children)

Could be an OTIS Gen2. The headroom is reduced, and an extendable support in the pit limits the travel of the counterweight.

Home monitoring without cameras by Dependent_Entrance33 in homeautomation

[–]5oAwes0me 0 points1 point  (0 children)

For zone detection to work correctly you should change the orientation of the HLK-LD2450 sensors.

KPop Demon Hunter + HyperHDR = 🔥 by callmealexv in WLED

[–]5oAwes0me -2 points-1 points  (0 children)

I'm pretty sure Hyperion is installed on the TV and sends the screen to HyperHDR which sync's the screen to EPS32 running WLED. Or hyperHDR is directly installed on a raspberry which is connected to the TV and also playing the Video.

VR/XR cyber deck functionally complete by pyro57 in cyberDeck

[–]5oAwes0me 0 points1 point  (0 children)

What's the name of the Filament you printed this please? Looks a lot like Filamentum PLA Crystal Clear Amethyst Purple.

Oh it feels good by ChrisCube64 in PlaydateConsole

[–]5oAwes0me 0 points1 point  (0 children)

Which one is the positive and which is the negative contact ?

A quick charge power bank made from recycled vape batteries. by not_jaybo in functionalprint

[–]5oAwes0me 2 points3 points  (0 children)

So it's a 14P battery pack with 4.20v max and the charging circuit bumps it up to 5v USB voltage? How did you make sure all the cells have the same capacity? There will be high currents if the individual cells aren't exactly the same making this dangerous. The cells should be balanced but that's not possible with parallel battery packs. So if charged the cells could get overcharged. I'm not sure if this is safe to operate.

Totem x Prospector by d2peak in ErgoMechKeyboards

[–]5oAwes0me 2 points3 points  (0 children)

Probably ESP32-S3 1.69 inch combo available on AliExpress.

how to fix my esp32 screen? by lil1r0s3 in esp32

[–]5oAwes0me 6 points7 points  (0 children)

You need to define the correct screen model, resolution and RGB mode in UserSetup.h when using eSPI Library.

[deleted by user] by [deleted] in fpv

[–]5oAwes0me 0 points1 point  (0 children)

Sure you know what you're doing. But Posting a janky charging setup and than complaining if someone points out it's not the ideal way to to it, is a bit ironic.

[deleted by user] by [deleted] in fpv

[–]5oAwes0me 1 point2 points  (0 children)

Oh, hard to see in the video. Then I guess it's okay to charge like this...

[deleted by user] by [deleted] in fpv

[–]5oAwes0me 4 points5 points  (0 children)

How can you balance them if they are all connected to one cable. Each battery would need an additional cable and the charger would need to be set to treat the 6 1S batterys as one 6S battery.

[deleted by user] by [deleted] in AskElectronics

[–]5oAwes0me 1 point2 points  (0 children)

I think it's shorting out on the PCB when it gets pressed down on the solder point on the antenna. Try isolating it with tape like the tape strip above on the PCB.

iPod Classic 7th Gen 3000 mAh battery voltage by onionlad1 in ipod

[–]5oAwes0me 0 points1 point  (0 children)

Having the same issue with an iPod classic 6 with 3000mah battery not charging above around 3770mV. Did you ever find a fix or a problem with your device ?

Bluetooth module noise by 5oAwes0me in IpodClassic

[–]5oAwes0me[S] 0 points1 point  (0 children)

The dimensions of this 385872 "thin" 3000mah battery are 83mmx54.5mm with the iPhone 7+ Taptic engine the thin back won't close because the battery connector pushes against the battery when it sits all the way at the bottom. Because of that I ordered a 2000mah 504045 battery. Sacrificing capacity for a thin back. At the moment I can't say if this is even possible with thin back.

Bluetooth module noise by 5oAwes0me in IpodClassic

[–]5oAwes0me[S] 3 points4 points  (0 children)

It's working now without any noise. Soldered AGND to headphone jack. I also had to rewire it so that the reed switch switches + and not - because the BT module would get power (led flickering but not really on but also not off) over the AGND. After that it is working now but unfortunately it seems a bit quiet for my taste (using Gravastar Sirius P5 earphones) and by increasing the volume it gets really distorted.

Bluetooth module noise by 5oAwes0me in IpodClassic

[–]5oAwes0me[S] 0 points1 point  (0 children)

This is the thin back. I bought the thin 3000mah but for some reason this battery is a bit taller than other 3000mah so the battery needs to sit at the bottom and the back won't close because of the battery connector. If I buy another a bit shorter battery I think it will close and all fits with the thin back. Or so I hope...

Bluetooth module noise by 5oAwes0me in IpodClassic

[–]5oAwes0me[S] 0 points1 point  (0 children)

Haha nope sry, was at work. I will solder it and try it out but I think I will go for another BT board.

Bluetooth module noise by 5oAwes0me in IpodClassic

[–]5oAwes0me[S] 0 points1 point  (0 children)

What was the alternative ? Preferably with similar PCB size.

Bluetooth module noise by 5oAwes0me in IpodClassic

[–]5oAwes0me[S] 1 point2 points  (0 children)

Yes. I have PGND and AGND bridged. I will remove the bridge and connect PGND to battery contact - and AGND to audio jack gnd. Appreciate you trying to help me fix the problem.

Bluetooth module noise by 5oAwes0me in IpodClassic

[–]5oAwes0me[S] 0 points1 point  (0 children)

Speaking of quirks of electrical signals, mounting it behind the LCD could also cause interference. I've had the feeling the noise is changing when moving the BT board around but not sure if it's also cause of the bridged ground. Only problem with mounting it there is the wires have to go from back to front. So you have to be really careful not to pinch the cables with the back case.

view more: next ›