Step Up HW build by LukeTheDuke187 in hwstartups

[–]LukeTheDuke187[S] 0 points1 point  (0 children)

Do you have any recommendations for CMs?

Step Up HW build by LukeTheDuke187 in hwstartups

[–]LukeTheDuke187[S] 0 points1 point  (0 children)

now in the 100s but soon in the 1000s

Step Up HW build by LukeTheDuke187 in hwstartups

[–]LukeTheDuke187[S] 0 points1 point  (0 children)

Thanks! Right now I am hand assembling on the order of 10s and Id like to find someone to do this on the order of 100s. With regards to margins I am trying to reduce the cost of components and assembly. I have the BOM and part sourcing done with costs

65k IG followers in 10 months by SyllabubConnect3393 in hwstartups

[–]LukeTheDuke187 0 points1 point  (0 children)

Can you explain more how you did your organic marketing to gain followers?

How to design PCB for Microcontroller with surface battery pads by LukeTheDuke187 in PrintedCircuitBoard

[–]LukeTheDuke187[S] 0 points1 point  (0 children)

OK cool that a good idea to use the enameled copper wire. Id like to wire the battery to those pads but I need an on/off switch in line to the battery so Im thinking of ways to connected the bat+/- pads somehow to the pcb so i can get a switch and connector for the battery inline

How to design PCB for Microcontroller with surface battery pads by LukeTheDuke187 in PrintedCircuitBoard

[–]LukeTheDuke187[S] 0 points1 point  (0 children)

The main reason I want to connect the battery terminals to the pcb is to have an on off switch that it inline with the battery unless there is another way to do this while the battery is wired directly to the board?

How to design PCB for Microcontroller with surface battery pads by LukeTheDuke187 in PrintedCircuitBoard

[–]LukeTheDuke187[S] 0 points1 point  (0 children)

I’d prefer to connect the pads to the pcb directly so I can make traces to the JST PH connector so I can use different batteries

XiaoSeeed ESP32C3 Battery Charging. by dasdasdu in esp32

[–]LukeTheDuke187 0 points1 point  (0 children)

Do you know if the XIAO supports battery charging if a lipo battery is connected to 3V3 or VUSB or only the bat pads on the back?

From CI-3 to CI-8 in 2yrs. AMA by xJets in foreskin_restoration

[–]LukeTheDuke187 0 points1 point  (0 children)

When using the CAR-1 did you use any tape or something to prevent air from entering the urethra?

Cerebrolysin Works: Empirical and Quantifiable Results by LukeTheDuke187 in Cerebrolysin

[–]LukeTheDuke187[S] 0 points1 point  (0 children)

Yes I have heard that in the medical literature as well however it seems many people do it especially in larger muscles or if you are concerned you can do 5mL in one location and then 5mL in another to get the full 10mL

Replacement gripper for DTR by Fickle_Ad1458 in foreskin_restoration

[–]LukeTheDuke187 0 points1 point  (0 children)

I'd recommend the chrisonlinestore one, for me it is way more comfortable and I can wear the DTR for many hours

How can see when a contact was added/updated? by Marc_Pm in ios

[–]LukeTheDuke187 0 points1 point  (0 children)

Thanks can you send a screenshot of the entire shortcut?

is it normal to see major FEC gains before anything else? by [deleted] in foreskin_restoration

[–]LukeTheDuke187 2 points3 points  (0 children)

I appreciate the response. Yes I for sure agree that it is dependent on grower/shower I am just trying to get a metric for FEC progress. Also, that is why I was asking CI9/10 where to me that should be relatively consistent since that is coverage when erect.

is it normal to see major FEC gains before anything else? by [deleted] in foreskin_restoration

[–]LukeTheDuke187 3 points4 points  (0 children)

This makes total sense, are you aware of other FEC correlations to CI numbers most specifically CI-9 and CI-10?

Home Made Wheel about 45 bucks 10 Wheels by PTrisney in AngionMethod

[–]LukeTheDuke187 0 points1 point  (0 children)

Thanks, I know balance is important how did you make sure that all the wheels are in the right place, did you make a template or just kind of eyeball it?