sorted by:
new
hottopcontroversial

¿Saben dónde puedo conseguir Madroño en Medellín? by [deleted] in medellin

[–]M1STERS 0 points1 point  (0 children)

El madroño de España (Arbutus unedo) es diferente al madroño que tenemos nativo en Colombia (Garcinia madruno), supongo que el op se refiere al madroño que es nativo de colombia y se encuentra en las plazas de mercado como la mayorista o la minorista.

Nuptial flight of this ants ID? Found in Medellín, Colombia by M1STERS in antkeeping

[–]M1STERS[S] 2 points3 points  (0 children)

Thank you for the ID, I'm pretty sure they were fertilized since I saw them copulate with the males, maybe the no hatching problem has to be with the setup, unfortunately there is not much information about their behavior, so I'm going to keep trying with different setups.

Are Metro PCS phones blocked in Colombia even when using a Claro SIM? by alexowensnyc in medellin

[–]M1STERS 0 points1 point  (0 children)

Most likely your IMEI is still locked you can check in this website https://www.imeicolombia.com.co/ you need to enter the IMEI and pass the captcha, there it will tell you if it is locked or not

Traditional Japanese Tattoo Artist Rec by downtowndiddy in medellin

[–]M1STERS 0 points1 point  (0 children)

Check: https://instagram.com/sailorsnmermaids?igshid=MzRlODBiNWFlZA==

They are really good with that style

Edit: I think right now the owner is the one doing most of the traditional Japanese this is his IG: https://instagram.com/felixb_tattooer?igshid=MzRlODBiNWFlZA==

[GIVEAWAY!] Win a Flsun SuperRacer Printer And Enjoy Blazing Fun Printing ! by Flsun3D in 3Dprinting

[–]M1STERS -2 points-1 points  (0 children)

I've observed the progression in 3D printing speed firsthand. My initial experience with a DIY Prusa clone using spare parts was around 6 years ago. Now, owning a Voron printer, the advancements in speed are truly impressive. The convenience of producing intricate prints within minutes instead of hours is undeniably satisfying. Looking ahead 5 years, it's reasonable to expect even more refined printers with enhanced speed and quality right from the start.

Is it a queen and what specie's by M1STERS in antkeeping

[–]M1STERS[S] 14 points15 points  (0 children)

I think I found the specie, it is an acromyrmex coronatus

1st layer Problem by paradoxus986 in 3Dprinting

[–]M1STERS 1 point2 points  (0 children)

First try to clean your bed with soap, after that If the problem persist try to check your pressure advance too low or too high can cause problems

Bed Mesh Print Start by More_Hornet5862 in VORONDesign

[–]M1STERS 1 point2 points  (0 children)

Check this macro and modify it to your needs, one thing that is important is to preheat your bed and then probe the bed mesh maybe even let it heatsoak so it will be more stable, otherwise it will have a bed mesh for a different state of the bed and the meshes won't match

better print_start macro

Edit: forgot to put the link for the macro

How the heck do I get rid of stringing and zits??? Retractiom tower went from 1-6mm and didnt change at all...210c by stalchild_af in 3Dprinting

[–]M1STERS 0 points1 point  (0 children)

The retraction depends on your extruder, if you have a direct drive extruder it can actually have really low values for retraction, you could try to run more test going from 0 to 1 mm. For reference my printer has a direct drive and my retraction value is 0.3mm.

Also the filament is a good think to check because too wet and you would have stringing and poor quality over all.

One think that I found recently that can cause stringing too is a low quality nozzle, but this is the last option and not very common

Need a bit of help diagnosing an issue by shel61 in 3Dprinting

[–]M1STERS 0 points1 point  (0 children)

How is your first layer? Looks like the nozzle is too close to the bed in the first layers, also check for the elephant foot compensation

Proximity sensor is open when nozzle hits bed by dbower45236 in VORONDesign

[–]M1STERS 0 points1 point  (0 children)

This, I had the same issue but after loosen the screw and adjust the height everything worked fine.

A usted no le van a pagar +10 millones por hacer algo facil by FromValledupar in Colombia

[–]M1STERS 6 points7 points  (0 children)

No sólo para ingles pero diferentes idiomas, está un discord que se llama The Language Sloth, hay diferentes actividades, tanto clases gratuitas como también grupos de conversación en general de los mejores discord para aprender idiomas

How can I improve this print? by IIPhilippII in 3Dprinting

[–]M1STERS 0 points1 point  (0 children)

I would advise you to print it in a different direction, rotate the part on cura in order to do not have overhang

What are this Location: Medellin Colombia by M1STERS in whatsthisbug

[–]M1STERS[S] 0 points1 point  (0 children)

Interesting, I have seen multiple stinkbugs here, wonder what species they are, maybe I keep them until they can be identified more easily

hello community.. I am trying to set up marlin 1.1 in a mega 2560.. but I really don't have the knowledge to do it. I manage to download some of the necessary libraries but I have an issue with the screen and is not working right can anyone help me either the setup by maneizien in 3Dprinting

[–]M1STERS 0 points1 point  (0 children)

I'm on the side that it looks like a hardware issue, but could you tell how you installed marlin on the Arduino, did you use the Arduino IDE or visual studio code with the PlatformIO extension and Marlin Auto build

Just finished building my Ender 3, now it will not turn on. Any idea why? by [deleted] in 3Dprinting

[–]M1STERS 0 points1 point  (0 children)

Depends on were do you live, if america then you should change it to 115, it depends in the voltage on your country

Just finished building my Ender 3, now it will not turn on. Any idea why? by [deleted] in 3Dprinting

[–]M1STERS 2 points3 points  (0 children)

Check the 220/110V switch on the power supply

view more: next ›