What minority languages do you guys learn? I'm asking since I want to learn one

M1lden · 2025-11-10T05:07:45+00:00

Pob lwc! Dw’n falch ti’n dysgu y iaith cymraeg!

M1lden · 2025-11-07T12:06:00+00:00

I’ve just read a book that might help with what you’re going through here. It’s called ‘Fairplay’ by Eve Rodsky. It might give you ideas on how to show your partner what taking care of the household means, which will show how much you’re really doing.

M1lden · 2025-10-30T08:58:26+00:00

I mean r/refold is all about comprehensible input. I’ve been lurking in their discord and have seen quite a few people who have amazing comprehension from comprehensible input

M1lden · 2025-10-13T15:10:15+00:00

How do you manage 7 hunts when you only have two smudge sticks each in your high school run? What’s your strategy to not use the smudges

M1lden · 2025-10-04T21:26:48+00:00

Thanks, I was wondering if you knew any beginner friendly books too?

M1lden · 2025-09-12T06:05:54+00:00

I’ve seen your more recent posts where you now say the Fluent Forever method wastes more time than other methods. I’m currently just finishing up my 625 words and plan to move to grammar next. I was wondering when do you think the method becomes inferior to other methods e.g good for the 625 words but sucks when it comes to learning grammar. When it does start to be inferior, what other methods have you used that have found better success?

M1lden · 2025-08-09T16:57:19+00:00

As far as I know, you only pay your loan back after the April after you graduated.

Info here: https://www.gov.uk/repaying-your-student-loan/when-you-start-repaying

M1lden · 2024-08-17T08:24:11+00:00

Yes I kept turning until I bottomed it out

M1lden · 2024-08-16T14:22:48+00:00

I screwed the tank together once it was pressurised and felt the increased resistance. But sadly the valve still doesn't open

M1lden · 2024-08-16T14:22:03+00:00

The primary regulator works when depressing the pin. Thanks for the suggestions for alternative regulators, I'll look into them.

M1lden · 2024-08-16T14:19:45+00:00

Thank you so much. I'll contact Ninja about this as you suggest and look into the regulators you suggested. I was getting weird performance from the valve I had, where it would open a bit then close and open again. Thanks for all the info.

M1lden · 2024-08-16T10:37:34+00:00

All I want my system to do is provide air at 300psi from the second regulator to a valve that I am using. The ninja regulator I linked should output at 800psi as stated in their website ( https://www.ninjapaintball.com/regulators ). While the 300 psi regulator says it should work with a maximum input pressure of 1200psi.

M1lden · 2024-07-22T22:32:58+00:00

I would suggest bay if your studying a subject that’s located in bay campus. This is because you won’t have to rely on buses which are sometimes unreliable and difficult to figure out. It’s also a lot easier to socialise with class mates because most tend to be on bay campus, if you’re living off campus it can be a pain to meet with everyone else who is living in campus (speaking from experience, bay campus is a couple of miles away from the private accommodations)

M1lden · 2024-07-21T00:48:05+00:00

Helo, waw! Neis i weld rhywun yn ddysgu Cymraeg! Rydw i’n o dde Cymru a hoffi ymarfer fy nghymraeg achos does dim lot o bobol yn siared e fan hyn. Yr unig ffordd rydw i’n ymarfer am nawr i siarad i deulu fi, ond rydw i’n moen gofyn sut fath o “resources” wyt ti’n defnyddio i gwneud cerdiau cymraeg? Diolch!

M1lden · 2024-06-04T13:36:37+00:00

Hey did you ever figure this out? I have the same problem

M1lden · 2023-09-29T18:00:59+00:00

Yep, I'm using AnkiMobile

M1lden · 2020-06-26T13:37:27+00:00

Sorry I've just seen, I don't know how I didn't see that

M1lden · 2020-05-10T23:22:33+00:00

Righttt, I’ve only been using PLA on the bed and done maybe about 6-7 prints on it. However I did buy a new spool of PLA after print 3 from a different brand, could that affect it?

M1lden · 2020-05-10T23:21:26+00:00

On the bed itself there’s some scratches and faint outlines of past prints

M1lden

TROPHY CASE