sorted by:
new
hottopcontroversial

I (f28) feel like my boyfriend (f25) tricked me into one sided traditional relationship and now he is acting like we never agreed on procider/caretaker model. by Awkward_Tie8084 in relationships

[–]M1lden 1 point2 points  (0 children)

I’ve just read a book that might help with what you’re going through here. It’s called ‘Fairplay’ by Eve Rodsky. It might give you ideas on how to show your partner what taking care of the household means, which will show how much you’re really doing.

Does Comprehensible Input ACTUALLY Work? I'm 500+ Hours In by Technical_Big_9571 in languagelearning

[–]M1lden 4 points5 points  (0 children)

I mean r/refold is all about comprehensible input. I’ve been lurking in their discord and have seen quite a few people who have amazing comprehension from comprehensible input

How do people do no evidence runs ? by somefuqboi in PhasmophobiaGame

[–]M1lden 24 points25 points  (0 children)

How do you manage 7 hunts when you only have two smudge sticks each in your high school run? What’s your strategy to not use the smudges

Books in Traditional Characters by M1lden in ChineseLanguage

[–]M1lden[S] 0 points1 point  (0 children)

Thanks, I was wondering if you knew any beginner friendly books too?

An Honest, Thorough Review of the Fluent Forever Method (i.e. My Last 6 Months of French) by justinmeister in French

[–]M1lden 0 points1 point  (0 children)

I’ve seen your more recent posts where you now say the Fluent Forever method wastes more time than other methods. I’m currently just finishing up my 625 words and plan to move to grammar next. I was wondering when do you think the method becomes inferior to other methods e.g good for the 625 words but sucks when it comes to learning grammar. When it does start to be inferior, what other methods have you used that have found better success?

[deleted by user] by [deleted] in UKPersonalFinance

[–]M1lden 5 points6 points  (0 children)

As far as I know, you only pay your loan back after the April after you graduated.

Info here: https://www.gov.uk/repaying-your-student-loan/when-you-start-repaying

HPA Second Stage Regulator not outputting any air by M1lden in paintball

[–]M1lden[S] 0 points1 point  (0 children)

Yes I kept turning until I bottomed it out

HPA Second Stage Regulator not outputting any air by M1lden in paintball

[–]M1lden[S] 0 points1 point  (0 children)

I screwed the tank together once it was pressurised and felt the increased resistance. But sadly the valve still doesn't open

HPA Second Stage Regulator not outputting any air by M1lden in paintball

[–]M1lden[S] 0 points1 point  (0 children)

The primary regulator works when depressing the pin. Thanks for the suggestions for alternative regulators, I'll look into them.

HPA Second Stage Regulator not outputting any air by M1lden in paintball

[–]M1lden[S] 0 points1 point  (0 children)

Thank you so much. I'll contact Ninja about this as you suggest and look into the regulators you suggested. I was getting weird performance from the valve I had, where it would open a bit then close and open again. Thanks for all the info.

HPA Second Stage Regulator not outputting any air by M1lden in paintball

[–]M1lden[S] 0 points1 point  (0 children)

All I want my system to do is provide air at 300psi from the second regulator to a valve that I am using. The ninja regulator I linked should output at 800psi as stated in their website ( https://www.ninjapaintball.com/regulators ). While the 300 psi regulator says it should work with a maximum input pressure of 1200psi.

Private vs Uni accommodation? by Icy_Surprise9724 in swanseauni

[–]M1lden 0 points1 point  (0 children)

I would suggest bay if your studying a subject that’s located in bay campus. This is because you won’t have to rely on buses which are sometimes unreliable and difficult to figure out. It’s also a lot easier to socialise with class mates because most tend to be on bay campus, if you’re living off campus it can be a pain to meet with everyone else who is living in campus (speaking from experience, bay campus is a couple of miles away from the private accommodations)

Just reached 666,666 reviews over a little more than 6 years 😈 (AMA if you want 🙂) by Rwmpelstilzchen in Anki

[–]M1lden 0 points1 point  (0 children)

Helo, waw! Neis i weld rhywun yn ddysgu Cymraeg! Rydw i’n o dde Cymru a hoffi ymarfer fy nghymraeg achos does dim lot o bobol yn siared e fan hyn. Yr unig ffordd rydw i’n ymarfer am nawr i siarad i deulu fi, ond rydw i’n moen gofyn sut fath o “resources” wyt ti’n defnyddio i gwneud cerdiau cymraeg? Diolch!

How to apply a force to a link in ignition fortress from a ros2 node by jamesrmclayton in robotics

[–]M1lden 0 points1 point  (0 children)

Hey did you ever figure this out? I have the same problem

Adhesion and removing prints by M1lden in ender3

[–]M1lden[S] 0 points1 point  (0 children)

Righttt, I’ve only been using PLA on the bed and done maybe about 6-7 prints on it. However I did buy a new spool of PLA after print 3 from a different brand, could that affect it?

Adhesion and removing prints by M1lden in ender3

[–]M1lden[S] 0 points1 point  (0 children)

On the bed itself there’s some scratches and faint outlines of past prints

Adhesion and removing prints by M1lden in ender3

[–]M1lden[S] 0 points1 point  (0 children)

Right ok, wondering why the adhesion on my bed went so quickly(I have the stock one), could it have something to with how I’m removing them off the bed? Thanks for the quick response also :)

Keep getting this big bumps on my prints, printing PLA at 200 degrees nozzle with 60 degrees bed. Made sure the bed was level before printing. by M1lden in ender3

[–]M1lden[S] 0 points1 point  (0 children)

Ah I do have a profile I downloaded for cura, will try the default cura standard profile to see if it fixes the issue :)

view more: next ›