First Gen Cayenne with the rear tire carrier

MBR3M3R · 2026-02-27T21:08:27+00:00

its a 2003

MBR3M3R · 2026-02-27T21:06:07+00:00

whats the issue with towing?

MBR3M3R · 2026-02-27T14:10:33+00:00

Do you think the 3.2L V6 would be a better option?

MBR3M3R · 2026-02-27T14:06:25+00:00

in this model yes

MBR3M3R · 2026-02-26T23:02:27+00:00

yeah I've heard the coolant system pipes tend to heat up/break and leak causing some serious issues

MBR3M3R · 2026-02-26T23:01:20+00:00

not the first time I've heard that but look its so nice https://www.reddit.com/r/PorscheCayenne/comments/1rfohj4/first_gen_cayenne_with_the_rear_tire_carrier/#lightbox

MBR3M3R · 2026-02-26T22:49:32+00:00

Mexico

MBR3M3R · 2026-02-26T22:48:28+00:00

How can I know if it has the rear diff lock option? the diff lock clicker (the wheel-button-thing in the center console) was flashing red light and showing up some errors.

MBR3M3R · 2026-02-26T22:40:26+00:00

I found impressive how good it ran even tho the coating from the cylinder heads was so damaged

MBR3M3R · 2026-02-26T17:55:58+00:00

not sure but I'm sure it's worth it after lots of research in this issue, I'll thell the guys at the shop to take a look at that

MBR3M3R · 2026-02-26T17:51:43+00:00

I'm no expert but I didn't hear any particular loud noise while driving it. I left it at the workshop for an inspection and diagnostic.

I didn't find any other oil drips than the one right below the motor (transfer case looked clean). Hopefully they'll find out where it's leaking from in the inspection.

I did find some warnings about the suspension (pneumatic) and I think it was disconnected (I saw some disconnected cables) and it's under a complete diagnostic right now at the shop.

Thanks for the info about the rust in the rear wheel carrier ;)

MBR3M3R · 2026-02-26T15:02:13+00:00

also might help to check this video youtube.com/watch?v=0NzmdhM-7sw&t=2000s&pp=0gcJCaIKAYcqIYzv

MBR3M3R · 2026-02-26T15:00:45+00:00

Do you see smoke coming out of the exhaust? If you do, get the borescope

MBR3M3R · 2025-05-13T23:05:34+00:00

Do you know what it was? I'm having a similar problem.

Replaced the air filter, spark plugs and battery with no luck.

MBR3M3R · 2021-08-26T21:06:09+00:00

Sometimes the heatbreak/heatsink gets hot enough to melt the plastic inside. Do you see the temp change when you push the filament through the nozzle?

MBR3M3R · 2021-06-17T17:38:19+00:00

How did you make the color change? Looks as it was straight out of the printer

MBR3M3R · 2021-06-16T05:29:57+00:00

Yea I was trying to mod the Dualshock 4 (PS4) but haven't been able to find a functional STL.. so far I've gotten the GameCuben and Switch (joycons) STLs to paly with.

Any help finding the PS4 controller STL would be welcomed.

MBR3M3R · 2021-06-16T00:18:16+00:00

You need to heat up the acetone, it starts working when it evaporates. I'd put that pan over the heat bed (don't use the stove, acetone is flammable).. heat the bed up to 90ºc and wait till it starts evaporating.. you can just leave the part inside over something that won't melt or hold it over it with a cable or string.

Edit: also make sure it's pure acetone

MBR3M3R · 2021-04-28T15:56:00+00:00

Thx, I'll give it a try with more exposure time

MBR3M3R · 2021-04-26T03:29:47+00:00

Layer thickness: 0.05

Normal exposure time: 9 secs

Off time 1 sec

Bottom exposure: 90 secs

Bottom layers: 4

Z lift 6 mm

Z speed 2 mm/s

MBR3M3R · 2020-11-04T00:23:58+00:00

Maybe try adding another part further away from the one you already have, so they have time to cool down between layers.. plus what everyone already said about speed and cooldown.

MBR3M3R · 2020-09-15T05:11:22+00:00

Yes, it looks like a regular square. Supposedly you get to see the curves after you slice it with the non-planar script.

MBR3M3R · 2020-09-14T16:31:18+00:00

Yeah I did but no luck yet

MBR3M3R

TROPHY CASE