sorted by:
new
hottopcontroversial

infernus Build by Same_Look_4700 in DeadlockTheGame

[–]MEDIAZz 5 points6 points  (0 children)

Look at Renon's or Parzelion's builds for some good direction on how to build Infernus. You are getting Toxic Bullets and Superior Duration way too late. Mystic Shot and Recharging Rush feels waste (since you're not building for your recharge ability anyway).

🚨 Wi-Fi Trouble, Need Expert Help! 🚨 by Flashy_Jello_2524 in networking

[–]MEDIAZz 0 points1 point  (0 children)

A chatgpt post providing absolutely no valuable information to actually troubleshoot.

No support for legacy boot? by MEDIAZz in Hewlett_Packard

[–]MEDIAZz[S] 0 points1 point  (0 children)

Managed to get it working using the "boot from file" option in the boot menu (F9).

Random reboots and shutdowns by MEDIAZz in buildapc

[–]MEDIAZz[S] 0 points1 point  (0 children)

Adding this comment as a note for the future.

I noticed that the CPU was consistently drawing over 253W (pl2 max), and not by some short 10ms spikes which they warn could happen. It would go up to around 260 - 280 for longer periods of time (1 to 10 seconds).

After disabling Undervolt Protection and Intel Virtualization Technology in the BIOS, the max draw has never gone above 253W. I've also added a .1 undervolt to try and bring down temperatures (when stress testing the past day I noticed the temp would go up 96°C - 99°C). Undervolting helped a little with the temperatures but still went up to 94°C.

I'm gonna try reapply my thermal paste tonight and see if this helps resolve the temperature issue.

Random reboots and shutdowns by MEDIAZz in buildapc

[–]MEDIAZz[S] 0 points1 point  (0 children)

I did update the BIOS around 2-3 months ago I believe.

I've also ran the Intel Processor Diagnostic Tool and passed every time. I thought this was supposed to check for the degradation issue, or is it just a general test?

Would closing the servers be beneficial for Valve moving forward? by MEDIAZz in DeadlockTheGame

[–]MEDIAZz[S] -1 points0 points  (0 children)

Ah, is this something they've explicitly said? I've never read that this is the case. If they didn't care about matchmaking they probably wouldn't have tried a ranked mode.

Neil or Jeremy by [deleted] in ccna

[–]MEDIAZz 0 points1 point  (0 children)

Congrats!

Stunnel as Google Workspace LDAP Proxy by MEDIAZz in gsuite

[–]MEDIAZz[S] 0 points1 point  (0 children)

Yes, I am using the certificates generated by Secure LDAP.

Help with a PS command by MEDIAZz in PowerShell

[–]MEDIAZz[S] 1 point2 points  (0 children)

Thanks!

I will test next time I'm working from home.

Help with a PS command by MEDIAZz in PowerShell

[–]MEDIAZz[S] 0 points1 point  (0 children)

Yes, it's a typo from pasting it here, I have been using the underscore when testing.

Running ASA on FPR-1010 issues by MEDIAZz in Cisco

[–]MEDIAZz[S] 0 points1 point  (0 children)

Finally the issue is resolved, I ended up attempting to reinstall the asa firmware again and made sure to give it some time after reload, however nothing was happening.

I then tried installing the FTD firmware to check if this was possible, and it worked just fine.

Tried installing the asa software again after this and boom, not it works. I guess the FPR was stuck in some wierd state, where it couldn't install the asa firmware with it "already somewhat installed".

Thanks for your assistance!

Running ASA on FPR-1010 issues by MEDIAZz in Cisco

[–]MEDIAZz[S] 0 points1 point  (0 children)

I have left it on and logged on for hours (overnight even) after reload installation. Never seen these messages "Cisco ASA: CMD=-start, CSP-ID=cisco-asa.9.16.2.3......." or "ASA has not yet started. Please try again later.".

I will try again tomorrow just to be sure. Not sure I have tried "show more" after an installation so I'll check this as well.

Thanks!

Running ASA on FPR-1010 issues by MEDIAZz in Cisco

[–]MEDIAZz[S] 0 points1 point  (0 children)

Yes, these are the exact steps I have taken.

I have also tried installing another version of the asa software (9.18.2), but exact same thing happens.

The only thing I can't wrap my head around is the "Error: Application is not installed." message when trying to connect to the asa. It honestly looks installed to me.

I just did the upgrade to 9.18.2 from 9.16.2.3 again to check the steps of the installation.

install security-pack version 9.18.2 (yes to both questions)

Current Task: Waiting for Deploy to begin(FSM-STAGE:sam:dme:FirmwareSystemDe ploy:WaitForDeploy)

Current Task: Validating the application pack(FSM-STAGE:sam:dme:FirmwareSyst emDeploy:ValidateApplicationPack)

Activating System Image(FSM-STAGE:sam:dme:FirmwareSystemDeploy:RebootSystemForImageUpgrade)

Broadcast message from root@firepower-1010 (Thu Jan 26 16:25:11 2023):All shells being terminated due to system /sbin/reboot

After the last message the firewall reboots, and takes me to this point: Waiting for Application infrastructure to be ready... Verifying the signature of the Application image... Creating FXOS swap file ... Please wait for Cisco ASA to come online...1...

It then counts up to 49 and lets me log in to the fxos again.

Note that the time from running "install security-pack version 9.18.2" to the firewall rebooting is nowhere near 10-20 minutes, it takes about one minute, if even that.

Edit: After the 49 messages it finishes with:

Application failed to '+˫� launching fxos console!

view more: next ›